OMRON Sensor Image Processing System FH Series FLV-DR[]Direct Ring Lighting Instruction Sheet

■Specifications

PRECAUTIONS FOR SAFE USE

Please observe the following precautions for safe use of the products. Item Model FLV-DR3220W FLV-DR4415W FLV-DR5030W FLV-DR6615W FLV-DR7000W FLV-DR7030W FLV-DR9000W FLV-DR9030W FLV-DR9215W FLV-DR12030W

1. Installation Environment FLV-DR3220R FLV-DR4415R FLV-DR5030R FLV-DR6615R FLV-DR7000R FLV-DR7030R FLV-DR9000R FLV-DR9030R FLV-DR9215R FLV-DR12030R • Do not use the product in environments where it can be exposed to

FLV-DR3220B FLV-DR4415B FLV-DR5030B FLV-DR6615B FLV-DR7000B FLV-DR7030B FLV-DR9000B FLV-DR9030B FLV-DR9215B FLV-DR12030B

inflammable/explosive gas.

• To secure the safety of operation and maintenance, do not install the Applicable Controllers FLV-TCC4□/-TCC1□/-TCC3HB□, FLV-ATC□1024-□

product close to high-voltage devices and power devices.

Lighting color (peak wavelength) W：White, R：Red(Typ.635nm), B：Blue(Typ.460nm)

Model FLV-DR□ • Tighten the screws with the specified torque in this document.

2. Power Supply and Wiring Light source LED

• For details on power supply and wiring, refer to PRECAUTIONS FOR LED Safety W, B: Risk Group 2 R:Risk Group 1　(IEC62471) SAFE USE on the INSTRUCTION SHEET of the dedicated controller

Direct Ring Lighting Electricity White 1.4W 2.7W 3.1W 5.0W 5.0W 5.0W 8.8W 8.1W 7.4W 11.9W

(FLV-TCC4□/-TCC1□/-TCC3HB□, FLV-ATC□1024-□).

• When connecting or disconnecting the lighting connector, be sure to turn Red 1.3W 1.7W 1.8W 3.9W 3.7W 3.7W 7.0W 6.6W 5.4W 9.8W

off the power of the unit. Not doing so may result in malfunction.

Blue 1.4W 2.7W 3.1W 5.0W 5.0W 5.0W 8.8W 8.1W 7.4W 11.9W　　

• The temperature may reach 70°C while power is being supplied under

INSTRUCTION SHEET thermally neutral environment. Do not touch the product directly. Be Insulation Resistance 20 MΩ (250VDC)

sure to wear heat-resistant gloves. Ambient Temperature Operating: 0 to ＋50℃, Storage: －15 to ＋60℃ (with no icing or condensation) • High-Voltage lines and power lines must be wired separately from this

Thank you for selecting OMRON product. This sheet product. Wiring them together or placing them in the same duct may Ambient Humidity Operating and storage: 35% to 85% (with no condensation)

cause induction, resulting in malfunction or damage. Degree of Protection IP20（IEC60529）

primarily describes precautions required in installing and

• Take sufficient safety measures such as fail-safe circuit to use the product.

operating the product. Vibration Resistance(destructive) 10 to 150 Hz, (0.7mm double amplitude) 80 min. each in X, Y, and Z directions

3. Others

Before operating the product, read the sheet thoroughly • Do not use in safety circuits for atomic energy or that are critical for human life. Shock Resistance (destructive) 150 m/s2 3 times each in 6 directions(up/down, left/right, forward/backward)

• Do not attempt to disassemble, deform by pressure, incinerate, repair, or

to acquire sufficient knowledge of the product. For your Materials Case：Aluminum

modify this product.

convenience, keep the sheet at your disposal. • When disposing of the product, treat as industrial waste. Weight Approx.60g Approx.70g Approx.60g Approx.120g Approx.110g Approx.120g Approx.230g Approx.200g Approx.200g Approx.360g

TRACEABILITY INFORMATION: • Be sure to connect a dedicated lighting controller (FLV-TCC4□/-TCC1□ Accessories Instruction sheet (this sheet) Importer in EU: Manufacturer: /-TCC3HB□, FLV-ATC□1024-□).Use of other devices may result in

Omron Europe B.V. Omron Corporation, fire, explosion, malfunction or failure. Wegalaan 67-69 Shiokoji Horikawa, Shimogyo-ku,

• If you notice an abnormal condition such as a strange odor, extreme

2132 JD Hoofddorp, Kyoto 600-8530 JAPAN

The Netherlands heating of the unit, or smoke, immediately stop using the product, turn off the power, and consult your dealer. • Do not drop or impose excessive vibration or shock on the product. It may cause breakdown of the product.

The following notice applies only to products that carry the CE mark:

• Ensure that all components which have locking mechanisms are locked

Notice:

before using the product.

This is a class A product. In residential areas it may cause radio

• Make sure not to drop the product when unpacking or moving it. ■Connection with Lighting Controller

interference, in which case the user may be required to take adequate

measures to reduce interference. 4. Applicable standards This lighting complied with the EN standard (EN61326) ・Mounting 　(Electromagnetic environment : Industrial electromagnetic environment

Align the positions of "the tab of the connector at the

　(EN/IEC 61326-1 Table 2))

• Also, the following condition is applied to the immunity test of this product. lighting cable" and "protrusion of the lighting connector at

© OMRON Corporation 2013 All Rights Reserved.

　There are case that Lighting brightness fluctuate  Max 10%. the Lighting Controller", and then insert it until it clicks.

Before mounting After mounting

PRECAUTIONS FOR CORRECT USE Observe the following to prevent failure, malfunctioning, and adverse effects Lighting Controller side on performance and the device.

PRECAUTIONS ON SAFETY

1. Installation site Do not install in the following locations:

● Meanings of Signal Words

• Locations where the ambient temperature exceeds the rated temperature range. Indicates a potentially hazardous situation which, if • Locations subject to sudden temperature changes (where condensation will form). not avoided, will result in minor or moderate injury, • Locations where the relative humidity is below or above 35 to 85% RH.

WARNING • Locations where there are corrosive or flammable gases.

or may result in serious injury or death. Additionally,

there may be significant property damage. • Locations where there is dust, salt, or iron powder. • Locations where the device will be subject to direct vibration or shock. Lighting side Indicates a potentially hazardous situation which, if • Locations where there is strong scattered light (laser light, arc welding light, ultraviolet light, etc.)

CAUTION not avoided, may result in minor or moderate injury

• Locations exposed to direct sunlight or next to a heater.

or in property damage.

• Locations where there is splashing or spraying of water, oil, or chemicals. • Locations where there is a strong electrical or magnetic field.

● Alert Statements in This Sheet ・Removing

2. Maintenance

• Do not install the product close to high-voltage devices and/or power devices Hold "the tab of the connector at the lighting cable" in the

WARNING in order to secure the safety of operations and maintenance.

arrow (←) direction and pull it straight.

• When this product and a cable are attached or removed, be sure to turn OFF

This product is not designed or rated for ensuring safety the power of the Controller first before operation. [Note]

of persons either directly or indirectly. Do not use it for • Never use paint thinner, benzen, acetone, or kerosene to clean the product.Wipe Do not pull out with excessive force without pressing the such purposes. the contamination with a soft cloth included a small amount of alcohol.

tab. Doing so may break the wire.

3. Power and cable connections

Do not disassemble the product. Doing so may cause

• When using a commercially available switching regulator, make sure that the

electric shock due to the high voltage portion. Burn also Before removing After removing

Frame ground terminal is grounded.

may result due to high temperature. Do not attempt to

• If there are surges on your power line, connect a surge absorber as

disassemble, deform by pressure, incinerate, repair, or Lighting controller side

appropriate for your conditions of use.

modify this product. • Before turning on the power after the wiring is completed, verify that the power is

correct, that there are no incorrect connections such as a shorted load circuit, and

Looking into the LED light continuously may cause visual

that the load current is suitable. Incorrect wiring may cause damage and failures.

impairment. Do not look directly into the LED light.

• Use the product with the specified voltage. Applying a voltage or AC voltage that exceed the rating may result in burning or explosion of circuit components. • For cable extension between the lighting and lighting controller, use an optional extension cable (FLV-XC□/-XC□R) or branch cable (FLV-XC□S2).Only

CAUTION Lighting side

one extension cable and branch cable can be used. • The bending radius at cable wiring must be at least 20 mm.

Do not use it exceeding the rated voltage.

4.Warming Up

There is a possibility of failure and fire.

After turning on the power supply, allow the controller to stand for at least 30 minutes before use. As the circuits are unstable immediately after power on,

Do not connect amplifier units to AC power supply.

brightness may gradually change.

Risk of explosion.

5. Lighting electricity Beware of danger of burns. Lighting electricity for lighting equipment to be connected to the Lighting Do not touch the case while the Lighting is ON or immediately Controller is limited. Be sure to check the lighting electricity written on the after the power is turned OFF, since it is extremely hot. plate of the product, label of the packaging box or this manual to connect a lighting within the specified value. 6. Static Electricity LEDs are easily damaged by static electricity. A grounded wrist strap should thus be used when installing or conducting maintenance on the Diffusion Board.