OMRON Sensor Image Processing Peripheral Equipment FLV Series FLV-LN[] Line Lighting Instruction Sheet

■Specifications

PRECAUTIONS FOR SAFE USE

Please observe the following precautions for safe use of the products. Item Model FLV- FLV- FLV- FLV- FLV- FLV- FLV- FLV- FLV- FLV- FLV- FLV-

1. Installation Environment LN82W LN142W LN322W LN442W LN122R LN222R LN322R LN422R LN82B LN142B LN322B LN442B • Do not use the product in environments where it can be exposed to inflammable/explosive gas.

• To secure the safety of operation and maintenance, do not install the product Applicable Controllers FLV-ATC□6024-□　

close to high-voltage devices and power devices.

Lighting color (peak wavelength) White Red(Typ.625nm) Blue(Typ.460nm)

Model FLV-LN□ • Tighten the screws with the specified torque in this document.

2. Power Supply and Wiring Light source LED

• For details on power supply and wiring, refer to PRECAUTIONS FOR SAFE LED Safety Risk Group 3 (IEC62471) Risk Group 1 (IEC62471) Risk Group 2 (IEC62471) USE on the INSTRUCTION SHEET of the dedicated controller (FLV-ATC□

Electricity 9.2W 18.4W 45.9W 64.3W 10.4W 20.7W 31.1W 41.4W 9.2W 18.4W 45.9W 64.3W

Line Lighting 6024-□).

• When connecting or disconnecting the lighting connector, be sure to turn off Insulation Resistance 20 MΩ (250VDC) the power of the unit. Not doing so may result in malfunction.

Ambient Temperature Operating: 0 to ＋50℃, Storage: －15 to ＋60℃ (with no icing or condensation)

INSTRUCTION SHEET • The temperature may reach 70°C while power is being supplied under

thermally neutral environment. Do not touch the product directly. Be sure to Ambient Humidity Operating and storage: 35% to 85% (with no condensation)

wear heat-resistant gloves. Degree of Protection IP20（IEC60529）

Thank you for selecting OMRON product. This sheet • High-Voltage lines and power lines must be wired separately from this product.

Wiring them together or placing them in the same duct may cause induction, Vibration Resistance(destructive) 10 to 150 Hz, (0.7mm double amplitude) 80 min. each in X, Y, and Z directions

primarily describes precautions required in installing and

resulting in malfunction or damage. Shock Resistance (destructive) 150 m/s2 3 times each in 6 directions(up/down, left/right, forward/backward)

operating the product.

• Take sufficient safety measures such as fail-safe circuit to use the product.

Materials Case：Aluminum　　 Cable：PVC

Before operating the product, read the sheet thoroughly 3. Others

• Do not use in safety circuits for atomic energy or that are critical for human life. Weight Approx.640g Approx.890g Approx.1950g Approx.2450g Approx.800g Approx.1320g Approx.1950g Approx.2400g Approx.640g Approx.890g Approx.1950g Approx.2450g

to acquire sufficient knowledge of the product. For your

• Do not attempt to disassemble, deform by pressure, incinerate, repair, or

Accessories Instruction sheet (this sheet)

convenience, keep the sheet at your disposal. modify this product.

• When disposing of the product, treat as industrial waste.

TRACEABILITY INFORMATION: • Be sure to connect a dedicated lighting controller (FLV-ATC□6024-□).Use Representative in EU: Manufacturer: of other devices may result in fire, explosion, malfunction or failure. Omron Europe B.V. Omron Corporation,

• If you notice an abnormal condition such as a strange odor, extreme heating of

Wegalaan 67-69 Shiokoji Horikawa, Shimogyo-ku,

2132 JD Hoofddorp, Kyoto 600-8530 JAPAN the unit, or smoke, immediately stop using the product, turn off the power, and

The Netherlands Ayabe Factory consult your dealer. ■Connection with the controller

3-2 Narutani, Nakayama-cho, • Do not drop or impose excessive vibration or shock on the product. Ayabe-shi, Kyoto 623-0105 JAPAN

It may cause breakdown of the product.

●Mounting

The following notice applies only to products that carry the CE mark: • Ensure that all components which have locking mechanisms are locked before

using the product. Align the groove of the cable with the protrusion of the

Notice:

This is a class A product. In residential areas it may cause radio • Make sure not to drop the product when unpacking or moving it. connector, and then push and rotate the screw clockwise.

interference, in which case the user may be required to take adequate 4. Regulations and standards

measures to reduce interference. This lighting complied with the EN standard (EN61326) with a EMC

directive (No.2004/108/EC). Before mounting After mounting

2279378-5C PRECAUTIONS FOR CORRECT USE

© OMRON Corporation 2013 All Rights Reserved. Controller side

Observe the following to prevent failure, malfunctioning, and adverse effects on performance and the device. 1. Installation site Do not install in the following locations: • Locations where the ambient temperature exceeds the rated temperature range. • Locations subject to sudden temperature changes (where condensation will form). PRECAUTIONS ON SAFETY • Locations where the relative humidity is below or above 35 to 85% RH. • Locations where there are corrosive or flammable gases. • Locations where there is dust, salt, or iron powder. Lighting side

● Meanings of Signal Words • Locations where the device will be subject to direct vibration or shock.

• Locations where there is strong scattered light (laser light, arc welding light,

Indicates a potentially hazardous situation which, if

ultraviolet light, etc.)

not avoided, will result in minor or moderate injury,

WARNING • Locations exposed to direct sunlight or next to a heater.

or may result in serious injury or death. Additionally, ●Removing

• Locations where there is splashing or spraying of water, oil, or chemicals.

there may be significant property damage.

• Locations where there is a strong electrical or magnetic field. Rotate the screw counterclockwise and pull the cable out of

2. Maintenance the connector.

Indicates a potentially hazardous situation which, if

• Do not install the product close to high-voltage devices and/or power devices

CAUTION not avoided, may result in minor or moderate injury

in order to secure the safety of operations and maintenance.

or in property damage.

• When this product and a cable are attached or removed, be sure to turn OFF Before removing After removing the power of the Controller first before operation.

● Alert Statements in This Sheet • Never use paint thinner, benzen, acetone, or kerosene to clean the product.Wipe

Controller side

the contamination with a soft cloth included a small amount of alcohol. WARNING 3. Power and cable connections • If there are surges on your power line, connect a surge absorber as

This product is not designed or rated for ensuring safety appropriate for your conditions of use. of persons either directly or indirectly. Do not use it for • Before turning on the power after the wiring is completed, verify that the such purposes. power is correct, that there are no incorrect connections such as a shorted load

circuit, and that the load current is suitable. Incorrect wiring may cause

Do not disassemble the product. Doing so may cause

damage and failures.

electric shock due to the high voltage portion. Burn also

• Use the product with the specified voltage. Applying a voltage or AC voltage

may result due to high temperature. Do not attempt to Lighting side

that exceed the rating may result in burning or explosion of circuit

disassemble, deform by pressure, incinerate, repair, or

components.

modify this product.

• For cable extension between the lighting and lighting controller, use an Looking into the LED light continuously may cause visual optional extension cable (FLV-XC□LN). There are four types of cable impairment. Do not look directly into the LED light. length: 1m/2m/3m/5m. Only one extension cable can be used. • The bending radius at cable wiring must be at least 40 mm. • In order to radiate a heat efficiently, set up the lighting with a space more than the heat radiation space (specified in the outline drawing) between the CAUTION lighting and other devices. 4.Warming Up

Do not use it exceeding the rated voltage. After turning on the power supply, allow the controller to stand for at least 30 There is a possibility of failure and fire. minutes before use. As the circuits are unstable immediately after power on,

brightness may gradually change.

Do not connect amplifier units to AC power supply. 5. Lighting electricity Risk of explosion. Lighting electricity for lighting equipment to be connected to the Lighting

Controller is limited. Be sure to check the lighting electricity written on the

Beware of danger of burns.

plate of the product, label of the packaging box or this manual to connect a

Do not touch the case while the Lighting is ON or immediately

lighting within the specified value.

after the power is turned OFF, since it is extremely hot.

6. Static Electricity LEDs are easily damaged by static electricity. A grounded wrist strap should thus be used when installing or conducting maintenance on the Diffusion Board.