Page 1
HP Design Jet Z5600 Post Script® Printer EN ZHTW Hardware Setup: 硬體設定： 1- open the printer box 1- 打開印表機包裝箱 EN Product Assembly 2- Stand assembly 2- 組裝機架 Instructions 3- Unpack more components 3- 取出其他組...
Page 2
EN Read these instructions carefully...What you will need for this procedure Product working area • Because the product is heavy, you may need three people to unpack it. When more than one person is n...
Page 3
EN Open the box HP Design Jet Z5600 Post Script® Printer JA 箱を開く Start Up ZHCN 打开包装盒 ZHTW 打開外盒 KO 상자 열기 ID Membuka kemasan © Copyright 2016 HP Development Company, L.P. EN Remove the accessories from ...
Page 4
EN Stand assembly JA スタンドを組み立てる ZHCN 底座组装 ZHTW 組裝機架 KO 스탠드 조립 ID Pemasangan dudukan EN Remove the pieces of cardboard. Lift up the sides and top of the printer box, and remove them Dismantle the botto...
Page 5
EN A screwdriver and 22 screws are provided in the stand Support one end of the cross-brace on the stand box Make sure you have used 4 screws in each leg. Remove the tray contents. box: 16 screws to a...
Page 6
4x EN Attach a foot to each leg, using four screws in each foot. IMPORTANT: Make sure there is nothing on top of the Remove the small flaps from each of the foam end pieces. Remove the tape from the t...
Page 7
EN Open the transparent covering and remove the desiccant Lift the stand, keeping it upside down. There is a round yellow button protruding from the top of Place the stand on the product slowly and ca...
Page 8
101.2kg EN When the legs are correctly located on the product, attach Check that the wheels on the stand are locked. Make sure there is nothing on top of the printer. Hold the product by the foam end ...
Page 9
EN Remove the foam end pieces. Remove the transparent covering from the product. Lay out the components of the basket. Fit the basket supports to the stand legs, one to each leg. JA スタンドの各脚部に、バスケットサポー...
Page 10
EN Fit the two short tubes to the product’s feet, one on the Attach the basket’s front tube to the two short tubes on Rest the basket’s rear tube on the supports that you have The basket is now comple...
Page 11
EN Unpack more components JA その他のコンポーネントを取り 出す ZHCN 打开更多组件的包装 ZHTW 取出其他組件 KO 추가 구성 요소 포장 풀기 ID Membuka kemasan komponen lain EN Remove all the orange tape pieces from the product, Open the Window. You...
Page 12
EN Turn the cardboard support 90° to the right. Carefully lift the cardboard support up and out of the prod- Inside the right-hand side of the product, you will see a Remove the cardboard carefully. u...
Page 13
EN Power and network configuration JA 電源およびネットワークを設定する ZHCN 电源和网络配置 ZHTW 配置電源和網路組態 KO 전원 및 네트워크 구성 ID Konfigurasi daya dan jaringan EN If you find a USB flash drive in a plastic bag inside the box, it...
Page 14
EN Printhead and cartridge setup JA プリントヘッドおよびカートリッ ジをセットアップする ZHCN 打印头和墨盒设置 ZHTW 印字頭和墨水匣設定 KO 프린트 헤드 및 카트리지 설치 ID Konfigurasi printhead dan kartrid EN Connect the power cable to the product’s power s...
Page 15
EN The product checks for the presence of ink cartridges. On Press the ink cover firmly into place until you hear Check that the ink cover is properly placed. Open the cover on the left-hand side of t...
Page 16
EN Insert the ink cartridges one by one. Each cartridge is The cartridges must be inserted the right way around: When you have inserted all of the ink cartridges correctly, the Open the window and gra...
Page 17
EN Pull the blue handle towards you as far as it will go. Lift the handle up to open the printhead cover. The setup printheads exist only to prevent the escape of Remove and discard all orange setup p...
Page 18
EN Press the OK key on the front panel when you have Unwrap each printhead and remove all orange parts. Insert the printheads one by one. Each printhead is marked Push each printhead into the slot unt...
Page 19
HP Design Jet Z5600 Post Script® Printer Start Up © Copyright 2016 HP Development Company, L.P. EN Pull the blue handle towards you as far as it will go, picking Push the handle down on top of the pri...
Page 20
EN Once the printhead check has finished the product will be When the front panel prompts you to load paper for If the blue removable stop is on the spindle, remove it. Put Push the removable stop tow...
Page 21
EN From the front of the product, place the spindle into the Feed the leading edge of the paper into the product until Media load for lower roll Go to the rear of the product, Remove the spindle by li...
Page 22
EN If the blue removable stop is on the spindle, remove it. Put Push the removable stop towards the roll as far as it will From the back of the product, place the spindle into the Feed the leading edg...
Page 23
EN HP e Print: Enable email printing 1 - Make sure that your printer is correctly connected to the Internet. 2 - Enable Web Services during initial setup of the printer, or later following the instruc...
Page 24
EN A screen appears explaining what steps you will Your network configuration connectivity will now be Your information will be verified, when complete, Congratulations! HP e Print is enabled on your ...
Page 25
HP Design Jet Z5600 Post Script® Printer Start Up hp.com/go/Design Jetclick © Copyright 2016 HP Development Company, L.P. EN Install the product software from the DVD that came with your printer onto ...
Page 26
EN You can now, or at some later time, color-calibrate the paper type that you intend to use in the product. Color calibration is 1. Return to home screen recommended for accurate color printing. It c...
Page 27
EN JA ZHCN ZHTW Note for MAC & Windows USB Mac および Windows の USB 接続 MAC 和 Windows USB 连接注意事 請注意，當 MAC 與 Windows USB connection: に関する注記： 项： 連線時： Do not connect the computer to the product yet. この時点...
Page 28
MAC 및 Windows USB 연결을 위한 Catatan tentang sambungan USB 안내 untuk MAC & Windows: Jangan sambungkan dulu komputer ke printer. Anda harus terlebih dulu menginstal perangkat lunak driver printer di kom...
