ESTES 3209 - Space Eagle User Manual

(Sold Separately)

*Porta Padell Launch Pad CEPSPACE EAGLE

*Electron Beam"” Launch Controller

Estes-Cox Corp.

。Recovery Wadding (302274)

1295 H Street, PO Box 227 FLYING MODEL ROCKET KIT INSTRUCTIONS

*Igniters (with engines)

Penrose, CO 81240-0227

*Igniter Plugs (with engines) KEEP FOR FUTURE REFERENCE.

Printed in Guangdong, China

*Estes Engines: B6-4 (First Flighti, C6-5

SA SN 入、

ASSEMBLY TIP Read all instructions before beginning work on your

OUT UNTIL FINAL

model. Make sure you have all parts

COUNTDOWNI!

1. Form loop with

and supplies.

shroud lines.

NOTE: Test 作 all parts together before applying glue.lf parts dontf properly sand as required for precision assembly.

IMPORTANT: Your Estes productis marked with afour digit let Code or codes, The code is two digits, a space and two more digits representing the week and year of manufacture, respectively. Lot codes can be found on the product package, decal, launch controllen, launch pad anay/or blast deflector Please record the lot code found onthe decal and keep for future reference. Lot code:

5. Tie 罗 to 加 with double knot.

4. Pull lines tight.

MASKING

1. Pull shock cord taut

when inserting INSERT KEY.

recovery wadding. PUSH DOWN

HARD AND Qty. Description Part Number 1 Engine Mount Tube 030408

BULB WILL

1 Engine Hook 035021

LIGHT.

1 Green Adapter Ring 030165-2 1 Engine Block 030224 1 Lower Body Tube 12” (30 cm) 031351

WHILE HOLDING KEY DOWN FIRMLY PRESS

squares recovery wadding. 1 Upper Body Tube 12 (30 cm) 031351

Push below shock cord LAUNCH BUTTON UNTIL LIFTOFFI!

1 Balsa Nose Block 070158

attachment.

6 Sonic Tubes 3" (72 mmy) 031305 6 Laser Cut Balsa Fins 065982

1 Balsa Nose Cone 073001

PRE-LAUNCH CHECK

J 1 Screw Eye 038251

This Paper

1. Separate igniter 2. Insert For safety, neverlaunch a damaged rocket, Check the rocket's body, nose cone

长 1 Shock Cord 038367

igniter. 4

and igniter plug. andg fins. Also, check the engine mount, recovery system and launch lug. Repair

L 1 Parachute 035815

any damage before launching the rocket.

1 Waterslide Decal (not shown) 065984

Can Be Recycled FLYING YOUR ROCKET

Choose a large field (500 ft [153 m] square) free of dry weeds and brown grass.

The larger the launch area, the better your chance of recovering your rocket. Football fields and playgrounds are great. Launch only with little or no wind and good visibility. su PPLIES In adqition to the parts included in the kit you will also need: Always follow the National Association of Rocketry (NAR) SAFETY CODE.

由 一 NO DRY GRASS

QOR WEEDS MISFIRES TAKE THE KEY OUT OF THE CONTROLLER. WAIT ONE MINUTE BEFORE

5. Gently <bend SS

GOING NEAR THE ROCKET! Disconnectthe igniter clips and remove the engine. igniters to 5 Take the plug and igniter out of the engine. Ifthe igniter has burned, it worked but form leads did not ignite the engine because it was not touching the propellant inside the

SCISSORS PENCIL RULER FINE CARPENTER'S MODELING MASKING WAX SPRAY SPRAY PAINT SPRAY PAINT

SANDPAPER GLUE KNIFE TAPE PAPER PRIMEB WHITE, BLACK “CLEAR COAT

as Shown. engine. Put a new igniter all the way inside the engine without bending it, Push

(#320-#400 GRIT) WHITE (OPTIONAL)

the plug in place. Repeat the steps under Countdown and Launch.

人 @2010 Estes-Cox Corp. All rights reserved. PN 65983 (3-10)