ESTES 2117 – Screaming Eagle
Summary
This comprehensive manual provides detailed step-by-step instructions for assembling a high-quality flying model rocket. Users will learn proper techniques for attaching fins, installing nosecones, mounting engines, and preparing the parachute recovery system. The guide emphasizes crucial pre-launch safety protocols—including required equipment checks and adherence to NAR standards—ensuring hobbyists can safely construct and successfully launch their powerful miniature rocketeers.
Page 1 Text Content
COUNTDOWN AND LAUNCH 人 EC SUPPLIES 了 GC 尺 EANM | NG EAG LEE- #2117
"Recovery Wadding (included with some engines) Www.estesrockets.com FLYING MODEL ROCKET KIT INSTRUCTIONS Porta Pad@ 1 Launch Pad ESTES-COX CORP KEEP FOR FUTURE REFERENCE *Electron Beam@ Launch Controller 1295 H Street 。Recommended Engines: A8-3, B4-4, B6-4, C6-5 Penrose, CO 81240 * lgniters and lgniter Plugs {included with Estes PRINTED IN CHINA engines)
KEY ASSEMBLYTIP: Read all instructions before beginning work on ALWAYS your model. Make sure you have all parts and supplies. OUT UNTIL FINAL TEST FIT ALL PARTS TOGETHER BEFORE APPLYING COUNTDOWNI! ANY GLUEI!lf any parts dont 全 properly sand as required for precision assembly.
PARTS Locate the parts shown below and lay them out on the table in front
ofyou. DO NOT USE THIS DRAWING TO ASSEMBLE YOUR ROCKET.
WHITE ENGINE
MOUNTTUBE WOo D DOWELS
BT-20J (1) 118"X9" (2)
-ae 共 、 (30408) (32054)
PLASTIC NOSE CONE
PNC-50E (1)
MASKING 从 1299) TAPE
GREEN A ADAPTER RING AR2050 (2) (30164-2)
GREEN ENGINE
BLOCK AR520
LAUNCH LUG 1/8"
X2 3/6" LL-2B (1
(38178) 必 __ PLASTIC PARTS SET (61300) /
INSERT KEY. PUSH DOWN FIRMLY AND
YELLOW SPACER 2
TOOL ET2 (T) AN
HOLD.
(35009) ENGINE HOOK RUBBER SHOCK
S CORD 14"X18" (TDEH-2 (1) (35021)
BALSA SHEET A (38368) {2) (61301)
WHILE HOLDING KEY DOWN, PRESS LAUNCH BUTTON UNTIL LIFTOFFI!
PRE-LAUNCH CHECK For safety, never launch a damaged rocket, Check the rockets body, nose cone and fins. Also, check the engine mount, recovery system and launch lug(s). Repair any damage before launching the rocket.
BALSA SHEET B
FLYING YOUR ROCKET 他 (61302) As SENBLEDPARACHUTE Choose alarge field (500 化 [152 m] square) free of dry weeds and brown grass. ( ) ) A The larger the launch area, the better your chance of recovering your rocket. Footbajifields and playgrounds are great. Launch only with little or no wind and 二 good visibility SUPPLIES In addition to the parts included in the kit you will also need:
-No b Ry GRAss Always follow the National Association of Rocketry (NAR) SAFETY CODE. 尖 人 才 仿ORWEEDS
MISFIR
TAKE THE KEY OUT OF THE CONTROLLER. WAIT ONE MINUTE BEFORE
GOING NEAR THE ROCKETI Disconnectthe igniter clips and remove the engine. SCc ISSORS PENCIL RULER FINE SANDPAPER ”CARPENTER'S GLUE ”MODELING KNIFE MASKINGTAPE HOBBY SAW Take the plug and igniter out of the engine. If the igniter has burned, it worked but 一 一 SPRAY PAINT 一
did not ignite the engine because it was not touching the propellant inside the 巡 (LIGHT GRAY, 必 K:engine. Put a new igni er all the way insiale the engine withou bending it. Push the NEUTRAL GRAY，
plug in place. Repeat the steps under Countdown and Launch. DRANGE，
PLASTIC SPRAY PRIMER INTERMEDIATE CLEAR SPRAY PRIMER WAX PAPER PAINT PEN SANDING BLOCK
/ CEMENT (WHITE) BLUE) (OPTIONAL) 区
PAGE8 名 2005 Estes-Cox Corp.Allrights reserved. PN 61139 (9-05) PAGE 1
Page Summary Contents For ESTES 2117 – Screaming Eagle
Manual Details
| Brand | Estes |
|---|---|
| Pages | 4 |
| File Size | 4.16 MB |
| Published | June 05, 2026 |
Enter the captcha to get the download link:
Frequently Asked Questions
What safety gear is required before launching a rocket?
Always follow the National Association of Rocketry (NAR) SAFETY CODE. Never launch a damaged rocket.
How should I prepare the launch area for optimal performance?
Choose a large field (152 m square) free of dry weeds and brown grass, and ensure little or no wind and good visibility.
What is the proper procedure for handling spent igniters?
If an igniter has burned but did not ignite the engine because it was not touching the propellant, put a new igniter all the way inside the engine without bending it.
How do I assemble the main wings and body tube sections?
Apply glue to beveled edges of right and left wing. Attach wings to body tube on a flat surface, holding until dry. Repeat for the other side.