HP HP DesignJet Z6200 Photo Printer Series - 42 inch Photo Printer Assembly Guide

Summary

Get essential setup guidance for your HP Designjet Z6200 large format printer. This manual provides comprehensive, step-by-step instructions covering the physical assembly of the unit's stand and components. Whether you are a professional designer or technical installer, the guide details optimal placement requirements, necessary tools, and software installation steps for both Windows and Mac operating systems, ensuring a seamless start to your printing workflow.

📄 Preview ‹ PAGE OF 31 ›

‹

HP HP DesignJet Z6200 Photo Printer Series - 42 inch Photo Printer Assembly Guide - Page 1

›

Page 1 Text Content

1. Printer engine / プリンタエンジン / / / EN The space required for assembly is

HP DESIGNJET Z6200 photo / / Mesin printer 1m 3m (10 feet) in front and 1m (3.5 feet)

3.5ft

at the sides and rear.

EN 42-in printer

JP 組み立てにはプリンタ前面に3m (10

Assembly Instructions 3m フィート)、側面および背面に1m

10ft (3.5フィート) のスペースが必要で

2. Stand / スタンドと用紙スタッカ

JP 42インチプリンタ / / / す。

組み立ておよびセットアッ Dudukan dan nampan ZHCN プ手順

3. Spare box / 予備の箱/ /

/ Boks suku cadang

ZHTW Ruang yang diperlukan untuk pemasangan adalah 3 m

(10 kaki) di depan dan 1 m (3,5 kaki) di samping dan

4. Supplies / サプライ品 / /

belakang.

/ / Persediaan

EN Please read these instructions carefully. These assembly instructions explain how to assemble the printer. Notice that the icons used in this document are also located on the printer packaging. The icons help you locate the parts needed at each stage of the assembly. Because spare screws are supplied, some screws will remain unused EN 4 people are required to perform certain tasks

42-in

after assembly of the printer.

Petunjuk pemasangan JP 特定の作業を行うために、4名必要です。

JP 以下の指示をよくお読みください。 - 以下の手順では、プリンタを組み立てる方法について説明します。この

マニュアルで使用されているアイコンは、プリンタのパッケージにも表示されています。アイコンにより、組 ZHCN

み立ての各段階で必要な部品を確認できます。予備のネジが同梱されているため、プリンタの組み立て後、何本かのネジが使用されないまま残ります。 ZHTW

Diperlukan 4 orang untuk menjalankan tugas tertentu.

EN Time required for assembly of the printer is ap- proximately 132 minutes. 2h JP プリンタの組み立て所要時間は約132分です。

Wakt u yang diperlukan untuk pemasangan printer adalah sekitar 132 m enit.

Bacalah petunjuk ini dengan cermat Petunjuk pemasangan ini menjelaskan cara memasang printer. Perhatikan

Sant Cugat del Vallès Barcelona · Spain bahwa ikon yang digunakan dalam dokumen ini juga terdapat pada kemasan printer. Ikon membantu Anda

Printed in XXX

Page Summary Contents For HP HP DesignJet Z6200 Photo Printer Series - 42 inch Photo Printer Assembly Guide

Page 1 1. Printer engine / プリンタエンジン / / / EN The space required for assembly is HP DESIGNJET Z6200 photo / / Mesin printer 1m 3m (10 feet) in front and 1m (3.5 feet) 3.5ft 3.5ft at the sides and rear. EN 42...

Page 2 EN Remove the packaging JP パッケージの開梱 ZHCN ZHTW Lepaskan kemasan EN Remove the boxes shown. JP 図のように箱を取り除きます。 Keluarkan boks yang ditunjukkan.

Page 3 EN Assemble the stand JP スタンドの組み立て ZHCN ZHTW Memasang dudukan EN Remove the box shown. Remove the first tray from the box shown. Remove the two boxes marked L and R from the first tray. JP 図のように箱を取り除き...

Page 4 Lower the left side of the cross-brace onto the box Locate the bag of screws and the screwdriver Remove the left leg from the box, and then remove the Lower the left leg onto the left side of the cros...

Page 5 Use four screws on the inside of the left leg to attach Use two screws on the outside of the left leg to attach Lower the right leg onto the right side of the cross- Use four screws on the inside of t...

Page 6 Use two screws on the outside of the right leg to attach Use four screws to attach the cross-bar to the legs. Notice that there is anti-slip material around two of the Place a foot on the left leg. Th...

Page 7 Use four screws to attach the foot to the left leg. Position the other foot on the right leg. There are pins Use four screws to attach the foot to the right leg. Roll the stand assembly into its uprig...

Page 8 EN Attach the printer engine to the stand JP スタンドへのプリンタエンジンの取り付け ZHCN ZHTW KO Pasang mesin printer ke dudukan Attach the left stand spacer to the top of the left leg. It Attach the right stand space...

Page 9 EN Remove the two packing pieces shown. Pull open the protective plastic from the base of the Lift the stand assembly onto the printer engine. The Use one screw to attach the right side of the stand t...

Page 10 Use two screws to attach the left side of the stand Place the spare box and the comsumables box against Rotate the printer onto the spare box and the Rotate the printer until the back of the printer r...

Page 11 Remove the pallet before lifting the printer to its Use the hand holds at the rear of the printer engine Remove the two foam end-packs, and then remove the Remove the anti-slip material from the two r...

Page 12 EN Assemble the bin JP 用紙スタッカを取り付ける ZHCN ZHTW Memasang nampan Remove the two brackets from the box that contains Use four screws to attach the brackets to the lower part Attach the two plastic bracket...

Page 13 Remove the bin assembly from the box that contains Insert the two bin arms into the bin cross-bar. Insert the bin cross-bar into the two plastic brackets. Click the ends of both bin arms into the meta...

Page 14 EN Unpack more components JP その他のコンポーネントの開梱 ZHCN ZHTW Membuka kemasan komponen lain Use the blue handle to open the bin. Remove the protective covering from the printer Remove the packing tapes marked...

Page 15 Open the printer window, and then remove the Remove the packing tape (1), then remove the packing Plug the Gigabit Ethernet cable into the Gigabit Pass the Gigabit Ethernet cable through the hook at E...

Page 16 EN Install the ink supplies JP インクサプライ品の取り付け ZHCN ZHTW Memasang persediaan tinta Plug the power cable into the rear of the printer, and Turn the Power switch to the On position at the If the power li...

Page 17 Wait until this message appears on the front panel Select your region and press OK to continue. Your region appears highlighted on the map for A message appears to inform you about supported (~1 minut...

Page 18 Wait until this message appears. The front panel To release the ink cartridge drawer, gently pull Shake the ink cartridge vigorously for about 15 Place the ink cartridge in the ink cartridge drawer. T...

Page 19 Push the ink cartridge drawer back into the printer The printer “beeps” when the cartridge is correctly Follow the same instructions to insert the other seven Open the window. EN until the drawer lock...

Page 20 When the above question on the front panel of your Open the printer window, and then remove the Remove the packing tape that is holding down the Pull up and release the blue latch on top of the EN pri...

Page 21 Before removing the setup printheads, look at each Lower the blue latch to close the printhead cover. Select: Wait until this message appears on the front panel. printhead and verify that each printhe...

Page 22 Pull open the maintenance cartridge door, which is Remove the transparent shipping tray. Wait until this message appears on the front panel Remove all of the setup printheads. EN located on the right ...

Page 23 Remove the two protective covers on the new Lower all of the printheads vertically into their correct Make sure that the printheads are correctly seated. If a “Reseat” message appears on the front pan...

Page 24 EN Close the carriage assembly cover. Make sure that the blue latch is correctly engaged, Close the printer window. Wait until the Ready for paper message appears on and then lower the latch. the fron...

Page 25 EN Load the paper JP 用紙の取り付け ZHCN ZHTW Isikan kertas Select the altitude where the printer is located. 1. Lift the spindle lock lever. Unlock and remove the blue hub from the left end of EN To select ...

Page 26 Slide one the rolls of paper that came with your printer Make sure that the black hub on the right side of the Slide the blue hub onto the spindle. Make sure that the With the blue hub on the left, lo...

Page 27 From the front panel, select the paper icon and then Select Load roll and then press the OK button. Insert the lead-edge of the paper into the printer, Confim the type and length of the paper roll tha...

Page 28 Macintosh* Windows** On the front panel, select the paper type and paper The printer automatically aligns the printheads and Please do not try to stop the paper advance; it is EN length of the roll th...

Page 29 EN ZHCN ZHTWJP Note for MAC & Windows USB Mac および Windows の USB 接続 MAC 和 Windows USB 连接注意事請注意，當 MAC 與 Windows connection: に関する注記：项： USB 連線時：請不要急著將電腦連接到印表機。您必須先在 Do not connect the computer to t...

Page 30 MAC 및 Windows USB 연결을 Catatan tentang sambungan USB 위한 안내 untuk MAC & Windows: Jangan sambungkan dulu komputer ke printer. Anda 아직 컴퓨터를 프린터에 연결하지 마십시오. harus terlebih dulu menginstal perangkat lun...

Page 31 Legal notices © Copyright 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set ...

Manual Details

Brand	HP
Pages	31
File Size	11.88 MB
Published	June 05, 2026

66 views

Enter the captcha to get the download link:

Frequently Asked Questions

What physical space is required for printer assembly?

You need 3m (10 feet) in front, and 1m (3.5 feet) at the sides and rear.

How many people are necessary to assemble this printer?

Four people are required to perform specific tasks during the setup process.

What is the correct procedure before installing the driver software?

Do not connect the computer to the printer first; you must install the printer driver software on your computer first.

What should I do if having trouble with the installation software?

If installation fails, re-install the software from: http://www.hp.com/go/Z6200/drivers