HP Designjet XL 3600 Multi-Function Printer Series HP Designjet XL 3600 MFP Series - Manual, Setup Guide

Summary

This comprehensive guide provides step-by-step assembly instructions for the large-format HP DesignJet XL 3600 MFP Series printer. Designed for technical installers and professionals, it covers everything from unpacking procedures and required workspace dimensions to essential tools like electric screwdrivers. The manual ensures a smooth setup process and detailed understanding of all components included in the kit, allowing users to correctly and safely operate their professional-grade large format printing system.

📄 Preview ‹ PAGE OF 40 ›

‹

HP Designjet XL 3600 Multi-Function Printer Series HP Designjet XL 3600 MFP Series - Manual, Setup Guide - Page 1

›

Page 1 Text Content

EN EN Please read these instructions carefully. These The size of the crate is 1616 mm x 766 mm x 1266 mm. The space required for

EN HP Design Jet XL 3600 MFPSeries

assembly instructions explain how to assemble the assembly is 1.5 m (5 feet) at the front and back and 3.7 m (12 feet) at the side.

Assembly Instructions printer. JA

クレートのサイズは 1616 mm x 766 mm x 1266 mmです。組み立てを

Because spare screws are supplied, some screws may

remain unused after assembly of the printer. 1m

JA HP Design Jet XL 3600 MFP 面にあります。

3.5ft

1.5 m ZHCN シリーズ包装箱的尺寸是1616 毫米 X 766 毫米 X 1266 毫米。组装所需的前端

5ft 空间是 1.5 米（5 英尺）在前面和后面，在侧面3.7米（12英尺）。

ZHTW 箱子尺寸為1616 公釐 X 766 公釐 X 1266 公釐。前方必須騰出 1.5 公尺

ZHCN JA （5 英呎）在前面和後面，在側面3.7米（12 英尺）。 HP Design Jet XL 3600 MFP 系列以下の指示をよくお読みください。以下の 12ft

手順では、プリンタを組み立てる方法について KO 상자 크기는1616 mm x 766 mm x 1266 mm입니다. 어셈블리에는 앞쪽에

説明します。 1.5 m 앞면과 뒷면, 옆면 3.7 m. 予備のネジが含まれているため、ネジは何本か ID

ZHTW HP Design Jet XL 3600 MFP 系列 Ukuran kemasan adalah 1.616 mm X 766 mm X 1.266 mm. Ruang yang diper

lukan untuk pemasangan adalah 1,5 m (5 kaki) di depan dan belakang dan

3,7 m (12 kaki) di samping.

KO HP Design Jet XL 3600 MFP 시리즈조립 지침 ZHCN

ID HP Design Jet XL 3600 MFP Series

由于提供了备用螺钉，在组装完打印机后，可能 EN 3 people are required to perform certain tasks.

Petunjuk Perakitan 会剩余一些未用的螺钉。 JA

特定の作業は、3名で行う必要があります。 ZHCN 某些任务需要 3 人完成。 ZHTW 某些工作需要 3 個人才能執行。

KO 일부 작업의 경우 두 사람이 필요합니다.

ZHTW 請仔細閱讀下列說明。這些組裝說明將解釋

ID Diperlukan 3 orang untuk menjalankan tugas tertentu.

EN Time required for assembly of the printer is approximately 100 minutes .

KO 이 설명서를 주의 깊게 읽으십시오. 이 조립 JA

ZHCN 组装打印机大约需要 100 分钟的时间。

ZHTW組裝印表機大約要花 100 分鐘的時間。

KO 프린터 조립에 소요되는 시간은 약 100분입니다. ID Waktu yang diperlukan untuk memasang printer adalah sekitar 100 menit.

ID Baca petunjuk ini dengan cermat. Petunjuk pemasangan ini menjelaskan tentang cara memasang

EN Tools required. These tools are not included, make sure you have them on the day of installation. Electric screwdrivers T10, T15,

printer.

T20, T25 Electric nut driver with 7mm adapter/wrench tool (10 points)/Cutter/ hammer/Lan cable.

Karena tersedianya sekrup cadangan, maka tidak

JA semua sekrup akan digunakan pada pemasangan 必要な工具: 注記：以下の工具は付属していませんので、インストールの日までに準備しておきます。電動スクリュー printer ini. ドライバー T10、T15、T20、T25/ 電動ナットドライバー 7mm/レンチ (10点)/ カッター / ハンマー / LANケーブル。 ZHCN 必备工具：注意：打印机并没有附带这些工具，请确保在安装时准备好这些工具。电动螺丝刀 T10、T15 、T20、T25/ 7mm 号电动螺母扳手/ 扳手工具（10 个点)/ 裁纸刀 / 锤子 / LAN 连接线。 ZHTW 必要工具：附註：未隨附這些工具，請確定您在安裝當天自備這些工具。電動螺絲起子 T10、T15、T20、T25/7mm 號套筒扳/扳手工具（10 點）/裁紙器 / 榔頭 / LAN 連接線。

Edition 3 KO

T10, T15, T20, T25/너트 드라이버 7mm// 자동절단기 / 망치 / LAN 케이블.

Large Format Division Camí de Can Graells 1-21 ID

08174 · Sant Cugat del Vallès Alat yang diperlukan: Catatan: perkakas ini tidak disertakan, pastikan Anda memilikinya pada saat pemasangan. Obeng listrik

Page Summary Contents For HP Designjet XL 3600 Multi-Function Printer Series HP Designjet XL 3600 MFP Series - Manual, Setup Guide

Page 1 EN EN Please read these instructions carefully. These The size of the crate is 1616 mm x 766 mm x 1266 mm. The space required for EN HP Design Jet XL 3600 MFPSeries assembly instructions explain how t...

Page 2 EN Crate contents ZHTW 箱內包含 1. Documentation: Assembly 1. 說明文件：組裝說明、簡介資訊。 Instructions, Introductory info 2. 電源線 2. Power cords 3.印表機 3. Printer 4.墨水匣 4. Ink cartridges 5.印字頭 5. Printhead 6.防傾斜支架 6....

Page 3 EN Unpacking the printer JA プリンタの開梱拆开打印机包装取出印表機 KO 프린터 포장 분리 ID Membuka kemasan printer 15’ EN Important: - Make sure to unpack on a flat floor - Keep packaging and security locks Note: When unpacki...

Page 4 EN Remove the 2 unfolded cardboard ramps. Fold the 2 cardboard pieces to create ramps: Use the tapes provided in the box to fix each ramp. Open the cardboard corner pieces. a) Fold one of sides 4 time...

Page 5 EN Assemble the lifters and remove the printer endcaps. Caution: Follow the process carefully to prevent structure deformation. JA リフタを組み立て、プリンタのエンドキャップを取り外し EN Remove the endcaps. Cut and remove the...

Page 6 EN Take the bag with the 2 lifters from the accessories box. Little by little screw the bolts to elevate the printer a few millimeters to be able to remove the endcap. Start on the right side of the p...

Page 7 EN Remove the endcap. Turn the screws a little at a time, first one side, then the Remove the lifters. Move the lifters to the left side of the printer. other, to lower the unit. Install one lifter on...

Page 8 EN Little by little screw the bolts to elevate the printer a few Remove the endcap. Turn the screws a little at a time, first one side, then the Remove the lifters. millimeters to be able to remove th...

Page 9 EN Fold in the 2 endcaps of the ramps. Open the plastic that covers the lower part of the product. Unlock the wheels and carefully slide the printer down. Remove the dessicant bags and printhead from ...

Page 10 EN Assemble the anti-tilt supports JA 傾き防止サポートの組み立て组装防倾覆支架組裝防傾斜支架 KO 경사 방지 지지대 조립 ID Pasang penahan anti kemiringan EN Lock the wheels. Insert 2 pins into each support; first insert the rear one (1)...

Page 11 EN Assemble the front panel JA フロントパネルを組み立てます组装前面板組裝前控制面板 KO 전면 패널을 조립합니다 ID Pasang panel depan EN Fix the pins into place with 2x T20 bolts in each support. Pull the cover’s sides apart slightly (1...

Page 12 EN Take the front panel support from the box Insert the support in the unit. Attach the support to the printer with 3 x T25 screws. Click the cover onto the support. Pass the cover and cables throught...

Page 13 EN Take the touchscreen from the box and place it onto a cloth Attach the arm to the front panel using 4x T25 screws. Insert the arm on the support and make sure it fits into Fix the arm to the suppor...

Page 14 EN Remove the screws from the stacker. Unfold the stacker. Slide the cover into place. Fix the cover of the front panel with a T15 screw. JA スタッカからネジを取り外します。スタッカを開きます。カバーを所定の位置にスライドさせます。 T15 ネジ 1本を使...

Page 15 EN Assemble the stacker JA スタッカーを組み立てる组装堆垛机組裝堆垛機 KO 스태커 조립 ID Pasang stacker EN Connect the cables to the front panel. Pass the cables through the gutter. Fix the stacker with 2 stacker screws. JA ケ...

Page 16 EN Remove the carton piece and attach the stacker cover by Insert the 6 deflectors. Identify the scanner door’s orange locker. Identify the scanner door’s orange locker. pushing it into place. JA 段ボール...

Page 17 EN Insert the key into the locker. Release the locker by pulling it hard with the tool. There is Open the scanner window. Note: Rotate the front panel to Rotate the locker horizontally and remove it. ...

Page 18 EN Remove the cardboard piece with tape on it. IMPORTANT: in the following step you must remove the Carefully remove the carriage retainer without touching the Close the scanner window. carriage retai...

Page 19 EN Remove the security locks JA セキュリティロックの取り外し取下固定锁拆除安全鎖 KO 보안 잠금장치 제거 ID Lepaskan kunci pengaman EN Remove the orange plastic piece from the back of the scan- Unscrew the T20 screw from the small ...

Page 20 EN Unscrew 2x T15 screws and the T20 from the lateral cover. Remove the lateral cover. Remove the T20 screw from the security lock. Remove the security lock: push the drawer up to release the pressure...

Page 21 EN Repeat steps 58 to 63 to remove the drawer locker on the HP Design Jet XL 3600dr only: Unscrew 2XT15 screws from HP Design Jet XL 3600dr only: Unscrew the T20 screw and HP Design Jet XL 3600dr only...

Page 22 EN HP Design Jet XL 3600dr only: Remove the T20 screw from HP Design Jet XL 3600dr only: Remove the security lock; HP Design Jet XL 3600dr only: Replace the lateral cover and HP Design Jet XL 3600dr o...

Page 23 EN HP Design Jet XL 3600dr only: Repeat the process on the If an extra drawer is not required; replace the covers and Assemble the basket. Remove all the plastic covering the drawers . Remove all othe...

Page 24 EN Connect the power cable to the printer, and the outlet. Switch the printer on . Select your language and altitude on the touch screen, If you find a USB flash drive in a plastic bag inside the box,...

Page 25 EN Printhead and cartridge setup JA プリントヘッドおよびカートリッジをセットアップする打印头和墨盒设置印字頭和墨水匣設定 KO 프린트 헤드 및 카트리지 설치 ID Konfigurasi printhead dan kartrid EN When prompted by the front panel to insert the ink Shake a...

Page 26 Close the ink cartridge covers (left and right). The printer will now prepare the ink system for use. When When prompted, open the scanner window. Lift up the printhead cover handle. the process finis...

Page 27 EN Pull the blue handle up as far as it will go. Open the printhead cover by pulling the handle down. Remove the orange caps from inside the carriage. Insert the printhead. JA 青いハンドルを、いっぱいまで上に引き出します。 ...

Page 28 EN Check the printhead is correctly alligned. Lift the printhead cover handle. Push the handle down to clip the cover to the bar. Pull the handle down to close the cover. Note: do not insert the nozzl...

Page 29 EN Push down to close the cover completely. Close the scanner window and press OK. The tubes will now fill. This will take about 15 minutes; please wait until completed before continuing. JA カバーを押して完全...

Page 30 EN Load paper and calibrate JA 用紙のセットとキャリブレーション装入纸张并进行校准裝入紙張並校準 KO 용지 공급 및 보정 ID Muatkan kertas dan lakukan kalibrasi 25’ Open the drawer. Remove the orange tapes. Open the right hub locking lever....

Page 31 EN Place the roll into the drawer between the hubs, with the Slide the right hub back towards the center until it engages Ensure that the hubs are fitted tightly to the roll on both Close the locking ...

Page 32 EN Feed the paper into the printer. Close the drawer when the rolls are loaded. In the front panel, choose the paper loaded. Calibration will take approx. 10-15 minutes. Important: Calibration must be...

Page 33 EN ZHTWConnectivity and Mobile Printing 連線與行動列印 1 - Make sure that your printer is correctly connected to the Internet. 2 - Enable the services during initial setup of the printer, or later following ...

Page 34 hp.com/go/Design Jetclick EN The connectivity wizard will now start and take you Install the product software on your computer. Radically simplify the printing experience: step by step through connect...

Page 35 EN ZHTWPrint from your smartphone or tablet - i OS users can print through Airprint (no installation is required), or download HP Smart App for enhanced printing capabilities. - i OS 使用者可以透過 Airprint（...

Page 36 Optional: Managing printer security in HP Connected. When you enable web services the printer is in unlock mode meaning everyone who knows the printer’s email You can now, or at some later time, color...

Page 37 EN Generate an EOI report EN Accessories: See instructions included on accessory box JA EOIレポートの作成 JA アクセサリ：アクセサリの箱に同梱され生成 EOI 报表製作 EOI 報告附件：请参阅附件包装箱上的说明 KO EOI 보고서 생성 配件：請參考配件包裝盒中隨附的說明 http:/...

Page 38 http://www.hp.com/go/Design Jet XL3600/VA EN HP’s Virtual Agent is there to troubleshoot issues with you at any time of day or night. Note: HP Virtual Agent available in selected countries. JA HPのバーチャ...

Page 40 EN © Copyright 2019-2021 HP Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the expres...

Manual Details

Brand	HP
Pages	40
File Size	14.33 MB
Published	June 03, 2026

64 views

Enter the captcha to get the download link:

Frequently Asked Questions

How long does the assembly take?

The printer assembly is estimated to take approximately 100 minutes.

What tools are required for setup?

Required tools include T10, T15, T20, T25 electric screwdrivers, a 7mm electric nut driver/wrench, cutter, hammer, and LAN cable.

What is the minimum space needed to assemble the printer?

You need 1.5m (5 feet) at the front and back, and 3.7m (12 feet) on the sides for setup.

Is everything included in the packaging?

The box does not include rolls or LAN cables.