ASUS Server Workstation Universal AP1710-E1 System Setup Quick Guide Manual User Guide
Summary
This comprehensive guide serves system builders, IT professionals, and technical technicians responsible for maintaining high-performance server hardware. The manual provides detailed, step-by-step instructions for assembling and configuring complex computer systems. It meticulously covers everything from CPU installation to memory setup, managing power connections, wiring various backplanes (SCSI, IDE), and connecting all associated chassis components like SATA drives and cooling fans, ensuring proper operation of enterprise server units.
Page 1 Text Content
Visit us at:
AP1710-E1 Server System Upper SCSI backplane
www.asus.com/products/server Cable connections
(On AS4/AS8 models) 1. Power cables (two 4-pin power plugs
CPU installation CAUTION Motherboard Optical drive from the power supply unit)
The CPU fits only in one correct orientation. 2. 68-pin SCSI signal cable (from the SCSI card
1. Signal cable (to the SEC_IDE connector
DO NOT force the CPU into the socket to connector)
1. Lift the socket lever and push it to
prevent bending the pins and damaging the on motherboard)
the other side. 3. HDD fan cable
2. Position the CPU above the socket. 2. Power cable (4-pin plug from the
4. SMBus cable (from the SMBus connector
Match the marked corner of the CPU power supply unit)
on the motherboard)
and the socket 5. SMBus cable (from the SMBus cable of the 3. Insert the CPU. lower SCSI backplane; for AS8 models only) 4. Push down the socket lever to secure the CPU. 5. Apply thermal grease on top of the CPU. 6. Install the CPU fan and heatsink.
1. ATX power cable (24-pin power plug from the power supply unit) 2. Power cable (8-pin ATX 12V power CAUTION plug from the power supply unit)
Memory installation
3. Power supply SMBus cable
A DDR DIMM is keyed with a notch to fit in
1. Press the 2. Align a DIMM on the 3. Insert the DIMM into the only one direction. DO NOT force a DIMM 4. CPU fan cable
retaining clips socket by matching the socket until the retaining into a socket to avoid damaging the DIMM.
5. SMBus cable to the backplane
outward. DIMM notch on the socket clips snap back in place.
6. Parallel port module cable
break.
7. Floppy disk drive signal cable (to FDD signal connector) 8. Optical disk drive signal cable Lower SCSI backplane (to ODD signal connector) (On AS8 models with cascade configuration) 9. Primary IDE connector
1 ~ 3. Same as upper SCSI backplane cables
10. Panel cable (to various chassis front 4. SMBus cable (from the SMBus cable of the panel connectors) upper backplane)
6. 68-pin SCSI signal cable to the SCSI connector
11. Chassis intrusion cable
of the upper backplane
12. SATA signal cables (7-pin cables HDD blower removal Chassis fan removal connected to the SATA connectors on the SATA backplane. Available on AA4 models only.)
1. Disconnect the fan cable. 1. Disconnect the fan cable
from the motherboard. 13. USB 2.0 cables (to USB 2.0 connector
2. Loosen the thumb screw.
on the front I/O board)
2. Press the fan tabs, then pull
3. Grip the blower case, then SATA backplane (On AA4 models)
the fan out of the chassis.
slide it out of the chassis.
1. Power cables (two 4-pin power plugs
3. Pull up the lock hooks of the
4. Remove the two screws on from the power supply unit)
chassis fan case.
the blower case. 2. SATA signal cables (from the SATA
4. Detach the chassis fan from connectors on the motherboard.
5. Remove the blower.
SCSI card (On AS4/AS8 models)
the case. 3. HDD fan cable
6. Refer to the User Guide for
5. Refer to the User Guide for 1. SCSI cable (to the top 68-pin SCSI connector
details. NOTE: For SMBus cable, refer to item #4 of the
details. on the first SCSI backplane)
section “Upper SCSI backplane.”
15-100518750 Copyright © 2004 ASUSTe K COMPUTER INC. All Rights Reserved. Technical Support Information: Asia-Pacific +886-2-2890-7123 • United States +1-502-995-0883 • Germany/Austria +49-2102-95590
Page Summary Contents For ASUS Server Workstation Universal AP1710-E1 System Setup Quick Guide Manual User Guide
Manual Details
| Brand | Server |
|---|---|
| Pages | 1 |
| File Size | 325.67 KB |
| Published | June 02, 2026 |
Enter the captcha to get the download link:
Frequently Asked Questions
How is the CPU installed in the motherboard socket?
Position the CPU above the socket, align marked corner points, and secure it by pushing down the socket lever. Note that the CPU fits in only one orientation.
What steps are needed to connect power or data cables during setup?
Connect specific cables (like 4-pin power plugs, DIMM, or SCSI signal cables) following their designated connectors. For detachable components like fans and blowers, disconnect them using provided tabs or screws.
Where can I find information on connecting the upper backplane?
Refer to item #1 section “Upper SCSI backplane” details for instructions on various connections (e.g., power cables, signal cables).
What is required when installing memory (DIMM)?
Align the DIMM by matching the notch and socket, then insert it in only one direction. The retaining clips will then snap back into place.