Panasonic SC-EN37 User Guide
Summary
Operating instructions for the Panasonic SC-EN37 CD Stereo System. The manual provides guidance on system setup, speaker connections, CD playback operations, and MP3 file compatibility. It includes a troubleshooting guide addressing common issues such as disc reading errors, sound quality problems, and speaker connectivity. The system consists of main unit SA-EN37 and speakers SB-EN37/SB-EN37A. Suitable for home audio enthusiasts seeking a compact stereo solution.
Page 1 Text Content
If you have any questions contact In the U.S.A.: 1-800-211-PANA (7262) Operating Instructions In Canada: 1-800-561-5505
CD Stereo System
Dear customer Thank you for purchasing this product.
Model No. SC-EN37
Before connecting, operating or adjusting this product, please read the instructions completely. Please keep this manual for future reference.
These instructions are applicable to the following systems. System SC-EN37 Main unit SA-EN37
SB-EN37
Speakers
SB-EN37A
Troubleshooting guide Before requesting service, make the following checks. If you are in doubt about any of the check points, or if the solutions indicated in the chart do not solve the problem, refer to the “Customer Services Directory” on page 7 if you reside in the U.S.A, or refer to the “Product information” on page 7 if you reside in Canada.
The disc isn’t correctly set.
No play. The disc is scratched or dirty. (Tracks skipped.)
There is moisture on the lens. Wait for about an hour and then try again. You may not be able to play MP3 if you have copied a multi-session disc that has no data between sessions.
MP3 cannot be read. When creating a multi session disc, it is necessary to close the session.
The amount of data on the disc is too small. Set the amount of data to greater than approximately 5 MB.
Sound is unfixed, reversed or comes
Check the speaker connections. (➡ page 3)•
from one speaker only.
Noise may occur when playing MP3 if recording quality is poor. Keep this unit away from mobile telephones if the interference is apparent.
No sound or there is a lot of noise. Turn the volume up.
Switch the unit off, determine and correct the cause, then switch the unit on. Causes include shorting of the positive and negative speaker wires, straining of the speakers through excessive volume or power, and using the unit in a hot environment.
Humming heard during play. An AC power supply cord or fluorescent light is near the cords. Keep other appliances and cords away from this unit’s cables.•
A beat sound or noise is heard while Switch the TV or other audio player off or separate it from the unit.
receiving a radio broadcast. Switch off the portable audio player connected to “MUSIC PORT”.
A low hum or noise is heard during AM Keep the antenna away from other cables and cords.
broadcasts. Keep the AM antenna away from the unit. The picture on the television near the
The location and orientation of the antenna are incorrect.
set disappears or stripes appear on the
The television antenna wire is too close to the unit. Separate the antenna wire of the television from the unit.
screen.
Check that the batteries are inserted correctly. (➡ page 2)
Remote control doesn’t work.
Replace the batteries if they are worn.
Display
You plugged the AC power supply cord in for the first time and there was a power failure recently. Set the time. (➡ page 6)•
PGM FULL The number of programmed tracks is limited to 24. No further tracks can be programmed.• NO PLAY A CD-ROM disc that is not CD-DA or MP3 format is inserted. It cannot be played.• ERROR Incorrect operation performed. Read the instructions and try again.• F76 There is a power supply problem. Consult the dealer.•
i Pod®
Verify that the i Pod battery is not depleted by attempting to turn it on without connecting it to the CD Stereo System.
i Pod does not turn on. Turn off both your CD Stereo System and i Pod before inserting it to the Dock. Power on the CD Stereo System and select the
appropriate source. The i Pod is not correctly seated into the Dock. Turn off the i Pod, remove it from the Dock connector. Reseat it and turn it on again.
No sound is coming from the speakers.
Make sure that i Pod is actually playing something. Adjust the volume.
Music is distorted or the sound level is
Check and make sure the equalizer function of your i Pod is turned OFF .•
too low.
Cannot control the i Pod from the CD Make sure the i Pod is inserted properly into the Dock.
Stereo System. Check the Dock connection and make sure that OPTION port is selected as the source of music. (➡ page 5) i Pod does not charge. Check all connections. (➡ page 3)•
Panasonic Consumer Electronics Panasonic Puerto Rico, Inc. Panasonic Canada, Inc.
Company, Division of Panasonic Ave. 65 de Infantería, Km. 9.5 5770 Ambler Drive En PC
Corporation of North America San Gabriel Industrial Park, Carolina, Mississauga, Ontario One Panasonic Way Secaucus, Puerto Rico 00985 L4W 2T3 New Jersey 07094 www.panasonic.ca http://www.panasonic.com
©2007 Matsushita Electric Industrial Co., Ltd. RQTV0224-3P
Printed in Malaysia H0107FL3047
SC-EN37_3P.indd 1 22/03/2007 17:15:00
Page Summary Contents For Panasonic SC-EN37 User Guide
Manual Details
| Brand | Panasonic |
|---|---|
| Pages | 8 |
| File Size | 3.91 MB |
| Published | June 16, 2026 |
Enter the captcha to get the download link:
Frequently Asked Questions
Why won't my iPod charge when connected?
Check all connections as per the manual on page 3.
What should I do if there is no sound from the speakers?
Check the speaker connections (page 3) and turn the volume up.
Why does the remote control not work?
Check that the batteries are inserted correctly or replace them if worn.
How do I resolve a 'NO PLAY' error with a disc?
A CD-ROM disc that is not CD-DA or MP3 format cannot be played.
What causes a humming noise during playback?
It may be caused by an AC power cord or fluorescent light near the unit's cables.