Panasonic AWEX500N User Guide and Manual
Summary
The AW-EX500 Signal Converter is a professional multi-format device designed to convert and manage various video signals, including analog, composite, Y/C, component, and SDI inputs. It utilizes interchangeable optional cards to support diverse output requirements in complex broadcasting environments. This manual provides essential operational guides, detailed connection instructions for both analog and SDI interfaces, setup steps, and comprehensive safety precautions necessary for safe installation and use. Ideal for video engineers or technical staff requiring flexible and robust signal routing solutions.
Page 1 Text Content
Signal Converter
AW-EX500N
Before attempting to connect, operate or adjust this product, please read these instructions completely.
Printed in Japan F0404S0 VQTB0001D
Page Summary Contents For Panasonic AWEX500N User Guide and Manual
Page 1
Signal Converter AW-EX500N Before attempting to connect, operate or adjust this product, please read these instructions completely. Printed in Japan F0404S0 VQTB0001D
Page 2
CAUTION: CAUTION TO REDUCE THE RISK OF FIRE OR SHOCK RISK OF ELECTRIC SHOCK DO NOT OPEN HAZARD, REFER MOUNTING OF THE OPTIONAL INTERFACE BOARD TO QUALIFIED CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOC...
Page 3
Contents Introduction................................................................................................. Precautions for use.................................................................
Page 4
Introduction The AW-EX500 signal converter can convert analog Listed below are the optional cards which can be used: composite, analog Y/C, analog component and SDI • AW-PB302 RGB Card (complying with...
Page 5
The AW-EX500 generates various sync signals internally When two optional cards are to be used in combination on the basis of the signals which are supplied to it. For this with the AW-EX100, remember ...
Page 6
Major operating controls and their functions <Rear View> <Side View> VIDEO/RGB/COMPONENT/YC OUT OPTION CARD Y/Y/VIDEO IN RS232C R-Y/C IN B-Y IN SDI IN DC12V IN AUDIO IN
Page 7
1Analog video output connector 2RS-232C connector [RS232C] [VIDEO/RGB/COMPONENT/YC OUT] This enables RS-232C communication via the AW-EX500 The analog video signals are output from this D-sub 9-pin be...
Page 8
Major operating controls and their functions 4Audio input connector [AUDIO IN] 8Power LED The audio signals are supplied to this connector. Input This lights up red when DC power is supplied to the DC...
Page 9
<Function setting switch 1 Set as shown below to match the analog signals which This is used to select the operations of the AW-EX500. are to be input to analog video input connectors 5, 6 Before c...
Page 10
Major operating controls and their functions 6: RS232C select <ADDITIONAL IF/OPTION IF> 9: Optional card slot optional card setting (Factory setting: OPTION IF) <PB302/PB310> (Factory sett...
Page 11
=Function setting switch 2 3: Analog RGB output SYNC addition setting This is used to select the operations of the AW-EX500. <SYNC ON/SYNC OFF> Before changing a setting, the power must be turne...
Page 12
Connections • Before proceeding with the connections, turn off the power. • Use the AW-PS505 AC adaptor to supply the power. Use the AW-CA4T1 power cable. • For further details on connecting the devic...
Page 13
Analog signal input Coaxial cable for video signals VIDEO OUT Coaxial cable (BELDEN 8281 or equivalent) VIDEO ...........................1 Zoom Lens Camera or Y/C ................................2 Com...
Page 14
Connections SDI signal input FUSE Zoom Lens Camera + SDI Card Coaxial cable (BELDEN 8281 or equivalent) SDI OUT Max. 200 m Convertible Camera AW —E600 Video monitor WV-CA9T5 VIDEO/RGB/COMPONENT/YC OUT...
Page 15
Attaching the rubber feet • Adhere the accessory rubber feet to the bottom panel when the AW-EX500 is to be placed on the floor for use. Rubber feet Standard accessories ORubber feet ....................
Page 16
Appearance Unit: inch (mm) VIDEO/RGB/COMPONENT/YC OUT OPTION CARD Y/Y/VIDEO IN RS232C R-Y/C IN B-Y IN SDI IN DC12V IN AUDIO IN (145 mm) 3- (10 mm) 3/ 4” (84 mm) (9 Dimensions: 3-5/16” (W) ~ 3-3/4” (H)...
Page 17
Specifications Power requirements: 12 V DC Power consumption: 6.85 W indicates safety information. Input DC 12V power input connector 270Mbps SDI (BNC) (SMPTE259M standard-compliant) Only video data s...
Page 18
Specifications Input/output interface: RS-232C Operating temperature: 14°F to 113°F (–10°C to +45°C) Operating humidity: 30 % to 90 % (without condensation) Dimensions (W!H!D): 3-5/16”!3-3/4”!6-1/8” [...
Page 20
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000 EASTERN ZONE...
Manual Details
| Brand | Panasonic |
|---|---|
| Pages | 20 |
| File Size | 283.30 KB |
| Published | July 15, 2026 |
0 views
Enter the captcha to get the download link:
Frequently Asked Questions
What is the operating temperature range for this device?
The recommended operating temperature is between 14°F (–10°C) and 113°F (+45°C).
Does connecting two optional cards affect signal synchronization?
Yes, when two optional cards are connected, they generate internal sync signals of 4Vp-p.
What must be done before connecting or disconnecting cables?
You must power off the device and ensure you avoid humid or dusty locations to prevent damage.