OMRON ZFV-C ZFV-C Smart Sensors Non-procedural Communication Command Reference
Summary
The ZFV-C is a sophisticated sensor and controller requiring precise external interaction. This comprehensive technical manual serves as an essential command reference for mastering non-procedural communication protocols. It guides advanced users, specifically those knowledgeable in electrical engineering, through setting up communication specifications (USB/RS-232C), acquiring settings data, executing complex measurements, and managing system parameters like SAVESAVE or LOADBANK commands. Use this guide to deeply integrate the ZFV-C into automated monitoring systems.
Page 1 Text Content
Smart Sensor ZFV-C
Non-procedural Communication Command Reference
Cat. No. Z244-E1-01
Page Summary Contents For OMRON ZFV-C ZFV-C Smart Sensors Non-procedural Communication Command Reference
Page 1
Smart Sensor ZFV-C Non-procedural Communication Command Reference Cat. No. Z244-E1-01
Page 2
1intro.fm 1 ページ ２００６年６月６日 火曜日 午後６時２９分 Introduction Thank you for purchasing the ZFV-C. This manual provides reference information on non-procedural communication commands for the ZFV-C. When using the...
Page 3
1feature.fm 1 ページ ２００６年６月６日 火曜日 午後６時３０分 Contents Contents Setting the Communication Specifications Format List of Non-procedural Commands Parameter List (ZFV-C) Acquiring/Sending Data Example of Usage...
Page 4
1feature.fm 2 ページ ２００６年６月６日 火曜日 午後６時３０分 Setting the Communication Specifications Setting the Communication Specifications Change the settings of the controller communication specifications for non-pro...
Page 5
1feature.fm 3 ページ ２００６年６月６日 火曜日 午後６時３０分 Format Format The format of non-procedural commands is as follows. Example: Command to execute measurement MEASURE command * Each character is output as an ASCI...
Page 6
1feature.fm 4 ページ ２００６年６月６日 火曜日 午後６時３０分 List of Non-procedural Commands List of Non-procedural Commands Command name Format Returned value Description BANKSET BANKSET OK <delimiter> Switches the...
Page 7
1feature.fm 5 ページ ２００６年６月６日 火曜日 午後６時３０分 Parameter List (ZFV-C) Parameter List (ZFV-C) The following parameters can be acquired or set by the DATASET or DATAGET command. "Common" parameters a...
Page 8
1feature.fm 6 ページ ２００６年６月６日 火曜日 午後６時３０分 Parameter List (ZFV-C) Area 1 (AREA1)/Area 2 (AREA2)/Area 3 (AREA3) Setting range/output Unit No. Parameter No. Parameter Remarks range Judgment -2: measurement...
Page 9
1feature.fm 7 ページ ２００６年６月６日 火曜日 午後６時３０分 Parameter List (ZFV-C) Unit No. Parameter No. Parameter Setting range/output range Remarks Average density 0 to 255 DATASET/DATAGET upper limit value compatible...
Page 10
1feature.fm 8 ページ ２００６年６月６日 火曜日 午後６時３０分 Parameter List (ZFV-C) Position (POSITION) Unit No. Parameter No. Parameter Setting range/output range Remarks Judgment -2: measurement off DATAGET compatible -...
Page 11
1feature.fm 9 ページ ２００６年６月６日 火曜日 午後６時３０分 Parameter List (ZFV-C) Character (CHARA1)/Character (CHARA2) Parameter Setting range/output Unit No. Parameter Remarks No. range Judgment -2: measurement off DA...
Page 12
1feature.fm 10 ページ ２００６年６月６日 火曜日 午後６時３０分 Acquiring/Sending Data Acquiring/Sending Data Flow of XMODEM communication When you capture image data by entering this command, image data is acquired and sen...
Page 13
1feature.fm 11 ページ ２００６年６月６日 火曜日 午後６時３０分 Acquiring/Sending Data Data transmission to ZFV-C from personal computer (issue of SYSLOAD command) Host device (personal ZFV-C computer) BANKLOAD/SYSLOAD comm...
Page 14
1feature.fm 12 ページ ２００６年６月６日 火曜日 午後６時３０分 Example of Usage Example of Usage The following describes an example procedure to communicate by non-procedural commands using Windows standard tool Hyper Term...
Page 15
1feature.fm 13 ページ ２００６年６月６日 火曜日 午後６時３０分 Example of Usage (3) Set the communication conditions. (4) Hyper Terminal is started up. 2. To facilitate command transactions, set echo and other communicatio...
Page 16
1feature.fm 14 ページ ２００６年６月６日 火曜日 午後６時３０分 Example of Usage (2) Select the Settings tab, and then ASCII Setup. (3) Mark the following checkboxes, and click OK to complete the setting. 3. Set the communi...
Page 17
1feature.fm 15 ページ ２００６年６月６日 火曜日 午後６時３０分 Example of Usage (1) Enter a command, and then press the return key. (2) The returned value corresponding to the command is returned from the controller. ZFV-C...
Page 18
1feature.fm 16 ページ ２００６年６月６日 火曜日 午後６時３０分 Example of Usage ZFV-C Non-procedural Communication Command Reference
Page 19
1feature.fm 17 ページ ２００６年６月６日 火曜日 午後６時３０分 Example of Usage ZFV-C Non-procedural Communication Command Reference
Page 20
1feature.fm 18 ページ ２００６年６月６日 火曜日 午後６時３０分 Example of Usage ZFV-C Non-procedural Communication Command Reference
Page 21
1feature.fm 19 ページ ２００６年６月６日 火曜日 午後６時３０分 Revision History Revision History Revision code Date Revised contents January 2006 Original production May 2006 Function added as per software version upgrade ...
Page 22
OMRON Corporation Industrial Automation Company Sensing Devices Division H.Q. Application Sensors Division Shiokoji Horikawa, Shimogyo-ku, Kyoto, 600-8530 Japan Tel: (81)75-344-7068/Fax: (81)75-344-71...
Manual Details
| Brand | Omron |
|---|---|
| Pages | 22 |
| File Size | 543.67 KB |
| Published | June 04, 2026 |
55 views
Enter the captcha to get the download link:
Frequently Asked Questions
How do I connect ZFV-C to an external communication device?
Use either a USB cable or RS-232C cable connection. If using USB, you must download and install the required driver by contacting your OMRON representative.
In what operational mode can non-procedural commands be accepted?
Communication commands are only accepted when the controller is switched to [RUN] mode, which executes the saving of specifications.
What is the indication if a non-procedural command fails or results in an error?
If the command was not executed successfully or the setting resulted in NG, the return value will be 'ER' (Error).