Dell Vostro 3580 Setup Guide & Specifications Sheet
Summary
This service manual provides comprehensive documentation for the product. The document includes detailed information about setup, configuration, operation, and maintenance of the desktop. It covers key features, specifications, installation procedures, troubleshooting steps, and best practices. The manual is designed for system administrators, IT professionals, and end users who need to deploy, manage, or operate the equipment effectively. Readers will find step-by-step instructions, technical diagrams, safety information, and reference materials to ensure proper usage and optimal performance.
Page 1 Text Content
Dell Vostro 3580 Service Manual
Regulatory Model: P75F Regulatory Type: P75F010
Page Summary Contents For Dell Vostro 3580 Setup Guide & Specifications Sheet
Page 1
Dell Vostro 3580 Service Manual Regulatory Model: P75F Regulatory Type: P75F010
Page 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of d...
Page 3
Contents 1 Working on your computer............................................................................................................................. Safety instructions.......................
Page 4
Installing the WLAN card.......................................................................................................................................... Solid-state drive/Intel Optane memory...
Page 5
Installing the display bezel ........................................................................................................................................ Camera...............................
Page 6
Working on your computer Safety instructions Prerequisite Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise noted,...
Page 7
Before working inside your computer About this task To avoid damaging your computer, perform the following steps before you begin working inside the computer. Steps 1 Ensure that you follow the Safety...
Page 8
Technology and components NOTE: Instructions provided in this section are applicable on computers shipped with Windows 10 operating system. Windows 10 is factory-installed with this computer. Topics: ...
Page 9
Figure 2. Thickness difference Curved edge DDR4 modules feature a curved edge to help with insertion and alleviate stress on the PCB during memory installation. Figure 3. Curved edge Memory Errors Mem...
Page 10
Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics 4K Support - Enables video resolutions far beyond 1080p, supporting next-generation...
Page 11
Speed Currently, there are 3 speed modes defined by the latest USB 3.0/USB 3.1 Gen 1 specification. They are Super-Speed, Hi-Speed and Full- Speed. The new Super Speed mode has a transfer rate of 4.8G...
Page 12
USB 3.0/USB 3.1 Gen 1 RAIDs Optical Media Drives Multimedia Devices Networking USB 3.0/USB 3.1 Gen 1 Adapter Cards & Hubs Compatibility The good news is that USB 3.0/USB 3.1 Gen 1 has been careful...
Page 13
Disabling Intel Optane memory About this task CAUTION: After disabling Intel Optane memory, do not uninstall the driver for Intel Rapid Storage Technology as it will result in a blue screen error. The...
Page 14
Removing and installing components Recommended tools The procedures in this document require the following tools: Phillips #0 screwdriver Phillips #1 screwdriver Plastic scribe NOTE: The #0 screw driv...
Page 15
Component Screw type Quantity Screw image I/O board M2x4 Optical-drive bracket M2x3 Optical-drive connector board M2x2 Big Head Power-adapter port M2x2 Power-button board M2x3 Power button with finger...
Page 16
Optical drive assembly Removing the optical drive assembly Prerequisites Follow the procedure in before working inside your computer Remove the SD memory card Steps 1 Remove the single (M2x5) screw th...
Page 17
Installing the optical drive assembly Steps 1 Align the optical drive bracket to the screw holes on the optical drive [1]. 2 Replace the two (M2x3) screws that secure the optical drive bracket [2]. 3 ...
Page 18
Next steps Replace the SD memory card Follow the procedure in after working inside your computer Base cover Removing the base cover Prerequisites Follow the procedure in before working inside your com...
Page 19
3 Pry the base cover from the top-right corner [1] and continue to open the right side of the base cover [2]. 4 Lift the left side of the base cover and remove it off the system [3]. Removing and inst...
Page 20
Installing the base cover Steps 1 Place the base cover on the palmrest and keyboard assembly [1]. 2 Press the right side of the base cover until it snaps into place [2, 3]. 3 Tighten the three captive...
Page 21
Next steps Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Battery Lithium-ion battery precautions CAUTION: Exercise caution wh...
Page 22
Removing the battery Prerequisites Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Steps 1 Disconnect the ...
Page 23
Next steps Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Memory modules Removing the memory module Pre...
Page 24
Installing the memory module Steps 1 Align the notch on the memory module with the tab on the memory-module slot. 2 Slide the memory module firmly into the slot at an angle [1]. 3 Press the memory mod...
Page 25
Next steps Replace the battery Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer WLAN card Removing the WL...
Page 26
Installing the WLAN card About this task CAUTION: To avoid damage to the WLAN card, do not place any cables under it. Steps 1 Insert the WLAN card into the connector on the system board [1]. 2 Connect...
Page 27
Next steps Replace the battery Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Solid-state drive/Intel O...
Page 28
4 Turn the thermal plate over. 5 Remove the single (M2x2) screw that secures the solid-state drive to the thermal plate [1]. 6 Lift the solid-state drive off the thermal plate [2]. Installing the M.2 ...
Page 29
3 Align the notch on the solid-state drive with the tab on the solid-state drive slot. 4 Slide and insert the tab solid-state drive into the solid-state drive slot [1]. 5 Tighten the captive screw tha...
Page 30
Removing the M.2 2280 Solid-state drive or Intel Optane memory - Optional Prerequisites Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive a...
Page 31
Next steps Replace the battery Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Coin-cell battery Removin...
Page 32
Installing the coin-cell battery Steps 1 With the positive-side facing up, insert the coin-cell battery into the battery socket on the I/O board [1]. 2 Press the battery until it clicks into place [2]...
Page 33
Next steps Replace the battery Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Hard drive Removing the h...
Page 34
4 Disconnect the interposer from the hard drive assembly. 5 Remove the four (M3x3) screws that secure the hard drive bracket to the hard drive [1]. 6 Lift the hard drive bracket off the hard drive [2]...
Page 35
Installing the hard drive assembly Steps 1 Align the screw holes on the hard drive bracket with the screw holes on the hard drive [1]. 2 Replace the four (M3x3) screws that secure the hard drive brack...
Page 36
4 Align the screw holes on the hard drive assembly with the screw holes on the palm rest and keyboard assembly [1]. 5 Replace the four (M2x3) screws that secure the hard drive assembly to the palm res...
Page 37
System fan Removing the system fan Prerequisites Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Remove th...
Page 38
3 Remove the three (M2.5x5) screws that secure the fan to the palm rest and keyboard board assembly [1]. 4 Lift the fan off the palm rest and keyboard board assembly [2]. Removing and installing compo...
Page 39
Installing the system fan Steps 1 Align the screw holes on the fan with the screw holes on to the palm rest and keyboard board assembly [1]. 2 Replace the three (M2.5x5) screws that secure the fan to ...
Page 40
4 Connect the ODD cable, display cable and fan cable to the system board [1, 2, 3]. Next steps Replace the battery Replace the base cover Removing and installing components
Manual Details
| Brand | Dell |
|---|---|
| Pages | 93 |
| File Size | 11.44 MB |
| Published | June 28, 2026 |
7 views
Enter the captcha to get the download link:
Frequently Asked Questions
How do I perform a WiFi power cycle?
Turn off computer, modem, and router. Wait 30 seconds, then turn router, modem, and computer back on.
What is the procedure for flea power release?
Turn off computer, disconnect power adapter, press and hold power button for 15 seconds, then reconnect adapter and turn on.
How do I get technical support from Dell?
Go to Dell.com/support, select your category, verify your region, and choose the appropriate support link.