Dell Chassis Management Controller for Dell EMC PowerEdge FX2 Version 2.3 Release Notes
Summary
Release notes for Dell Chassis Management Controller (CMC) version 2.3 for the Dell EMC PowerEdge FX2 modular chassis (July 2020), documenting platforms affected, license requirements, supported features, new capabilities, resolved fixes, important notes, and known issues. Notes discrepancies including different PCIe card device names displayed on iDRAC versus CMC GUIs and errors during CMC configuration file import. Covers firmware update procedures for the FX2 converged infrastructure platform
Page 1 Text Content
Dell Chassis Management Controller for Dell EMC Power Edge FX2 Version 2.3 Release Notes
July 2020 Rev. A00
Page Summary Contents For Dell Chassis Management Controller for Dell EMC PowerEdge FX2 Version 2.3 Release Notes
Page 1
Dell Chassis Management Controller for Dell EMC Power Edge FX2 Version 2.3 Release Notes July 2020 Rev. A00
Page 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of d...
Page 3
Contents Chapter 1: Dell Chassis Management Controller for Dell EMC Power Edge FX2..................................... Chapter 2: Platforms Affected......................................................
Page 4
Dell Chassis Management Controller for Dell EMC Power Edge FX2 The Dell Chassis Management Controller (CMC) for Dell EMC Power Edge FX2 is a System Management hardware and software solution for managi...
Page 5
Platforms Affected Dell Chassis Management Controller (CMC) for Dell Power Edge FX2 supports the following: Chassis: Dell Power Edge FX2 Dell Power Edge FX2s Sleds: Dell Power Edge FC640 Dell Power Ed...
Page 6
License Requirements CMC supports software licensing to use advanced systems management features. For more information, see the Dell Chassis Management Controller for Dell EMC Power Edge FX2 User's Gu...
Page 7
What is Supported Supported Web Browsers and Operating Systems Microsoft Internet Explorer 11 Microsoft EDGE Safari 12.1.2 Safari 13.0.4 Mozilla Firefox 72 Mozilla Firefox 73 Google Chrome 79 Google C...
Page 8
What is New Addressing Open Source security vulnerabilities. Enhancing chassis profile to configure i DRAC network parameters. Applying server profiles using racadm command line interface. Release 2.2...
Page 9
Extending SNMP protocol and custom discovery port configuration in GUI. Extending SNMPv3 trap configuration support in WSMan. Configuring CMC using WSMan for the following SNMPv3 user attributes: user...
Page 10
Create and deploy a library of Boot Identity Profiles (boot from i SCSI/SAN configurations) to enable quick restore of workload to a spare server. Populate i DRAC DNS setting from the CMC Quick Deploy...
Page 11
Fixes Fixed an issue causing Internal server error observed while deleting virtual disk. Fixed an issue causing FANs are running at 30% PWM across all the interfaces during single-server i DRAC firmwa...
Page 12
Release 1.32 Fixed the Server/Host operating system Network Flap issue, which occurs occasionally on Modular platforms for a short duration during CMC initialization. Fixed the Server/Host operating s...
Page 13
Important Notes CMC network default setting is Static with IP address of "192.168.0.120". Complete the CMC network setup by directly connecting a client system on the same network. For more ...
Page 14
Known Issues Topics: Different PCIe card device name displayed on the i DRAC and CMC GUIs Error occurs while importing CMC configuration file Value of power available for server power on increases aft...
Page 15
Versions/Systems All CMC versions for Power Edge FX2 2.10 using OM 911 and later. affected Tracking number Static IPv6 IP address can be assigned to i DRAC blades Description Static IPv6 IP address ca...
Page 16
Limitations Issue 1: Description In the Microsoft Edge browser, the Boot Identity Profiles page in the CMC GUI is slow when 1500 or more MAC addresses are created from the MAC pool for the Boot Identi...
Page 17
PSOC Read Me Release Version:13 Added I2C master module to read temperature sensor as master. Allocated space in the DPM for enable/disable temperature sensor reading as master and sensor reading conf...
Page 18
Installation Prerequisites See the Dell Chassis Management Controller for Dell EMC Power Edge FX2 Version 2.3 User's Guide for the following information: Prerequisites Hardware and software requiremen...
Page 19
Accessing documents from Dell Support site Latest Release Notes To access the latest Release Notes for this version, follow these steps: 1. Go to https://www.dell.com/cmcmanuals. 2. Click the link for...
Page 20
Contacting Dell EMC NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell EMC product catalog. Dell provides se...
Manual Details
| Brand | Dell |
|---|---|
| Pages | 20 |
| File Size | 97.68 KB |
| Published | June 17, 2026 |
6 views
Enter the captcha to get the download link:
Frequently Asked Questions
What specific hardware models are supported by the CMC Controller?
It supports Dell PowerEdge FX2 and various sleds, including FC640, FD332, and DC830.
What operating systems can connect to the CMC GUI?
Supported OS include IE 11, Microsoft EDGE, Safari (12.1.2/13.0.4), Firefox (72/73), Chrome (79/80).