Futaba 6EXP User Manual and Instructions
Summary
Master the sky with this comprehensive guide for the Futaba 6EXP digital proportional radio control system. Designed for advanced performance in both airplanes and helicopters, this manual is perfect for sport flyers or beginners looking to upgrade their RC setup. It provides exhaustive instructions on setup, covering everything from signal connection and basic model settings to complex aerial functions like GYRO/REVO mixing, Idle-Up Throttle Curves, and specialized ACRO/HELI modes. Safely program your radio and maximize flight control experience with detailed steps and flow charts.
Page 1 Text Content
INSTRUCTION MUNUAL for Futaba 6EXP 6-channel, PCM/PPM(FM) selectable Radio control system for Airplane/helicopter
Futaba Corporation
Technical updates available at: http://www.futaba-rc.com
Entire Contents © Copyright 2006
Page Summary Contents For Futaba 6EXP User Manual and Instructions
Page 1
INSTRUCTION MUNUAL for Futaba 6EXP 6-channel, PCM/PPM(FM) selectable Radio control system for Airplane/helicopter Futaba Corporation Technical updates available at: http://www.futaba-rc.com Entire Con...
Page 2
TABLE OF CONTENTS Introduction ..........................................................................3 (HELI functions) N-TH Normal Throttle Curve........................................24 Service...
Page 3
INTRODUCTION Thank you for purchasing the Futaba 6EXP digital proportional R/C airplane/helicopter system. If this is your first “computer” radio, rest assured that it is designed to make initial setu...
Page 4
CONTENTS AND SPECIFICATIONS Transmitter: T6EXP Servos: S3004/S3003 T6EXP Transmitter with 6-model memory. S3004 ball bearing/S3003 standard servo with mounting hardware and servo arm assortment Transm...
Page 5
Receiver crystals: The receiver frequency may be changed as long as it remains within the “low” and “high” band frequency range. If your receiver is on any channel from 11 through 35, it is a “low ban...
Page 6
INTRODUCTION TO THE 6EXP SYSTEM IMPORTANT!: Always turn on the transmitter first, then the receiver. When turning off the system, always turn off the receiver first. The object is never to have the re...
Page 7
H:Throttle – hold switch - This switch operates to hold the engine in the idling position and disengaged it from the Throttle Stick. It is commonly use to practice auto-rotation. Neck strap hook - Mou...
Page 8
RADIO INSTALLATION Follow these guidelines to properly mount the servos, receiver and battery. INPORTANT!: Please use PCM receiver if the composition parts of the model used much metal, carbon graphit...
Page 9
• IMPORTANT: NEVER cut the receiver antenna or mount it in the model folded back on itself. Doing so will change its electrical length, possibly reducing the distance from the pilot that the model can...
Page 10
RECEIVER AND SERVO CONNECTIONS Connect the servos to the receiver to perform the functions indicated: Receiver Function output channel Aircraft (ACRO) Helicopter (HELI) Aileron -or-right flaperon -or-...
Page 11
CHARGING THE Ni-Cd BATTERIES The transmitter and receiver batteries included with your 6EXP system are rechargeable, Ni-Cd (nickel-cadmium, pronounced ni-kad) batteries. Ni-Cd batteries require specia...
Page 12
LIQUID CHIP DISPLAY (LCD) & PROGRAMMING CONTROLS MODE key - use to select desired function while programming Throttle-cut button - To use the throttle-cut function, To open programming menu; Press...
Page 13
Transmitter battery voltage “Battery” icon In addition to the model type, the LCD screen also displays the transmitter battery voltage. When the voltage goes below approximately 8.5 Volts the “battery...
Page 14
PROGRAMMING THE 6EXP RADIO Anytime you wish to view or change any of the current settings in the transmitter, the programming mode must first be entered by, of course, turning on the power, then by pr...
Page 15
ACRO/HELI Model type select function The Model type select function is used to select the ACRO or HELI mode of model type. ACRO: Powered aircraft memory type (with multiple wing and tail configuration...
Page 16
Model name function Assign a name to the model memory. By giving each model a name that is immediately recognizable, you can quickly select the correct model, and minimize the chance of flying wrong m...
Page 17
the throw. 5. Repeat the procedure for the other dual rate (channel 2-elevator, 4-rudder). EXPO Exponential Settings The “exponentials” are in the same function as the dual rates. (Pressing the MODE k...
Page 18
TRIM Trim Settings There are four trim levers (“trims”) on the front of the transmitter. Three of the trims are for adjusting the neutral position of the aileron, elevator and rudder servos. The fourt...
Page 19
PMIX1/2 Programmable Mixer 1/2 (ACRO only) Unlike the “wing mixing” function (explained later) where the channels to be mixed are factory-set, the T6EXP also contains two programmable mix where the yo...
Page 20
Wing Mixing Type Selection (ACRO only) With the programmable mix (previously described) the user determines the two channels to be mixed. The wing mixing function is another mix that may be used, but ...
Page 21
To activate flap trim: 1. Enter the programming mode. Access the “FLTR” screen with the MODE key. 2. If “INH” is blinking, push DATA INPUT lever upward for 0.5 seconds. Then you will see that the blin...
Page 22
4. Next you may the elevator setting. Press the SELECT key to display the “CH2” and flashing “%” sign. Use the DATA INPUT lever to set the percentage of elevator travel rate from -100% to +100% 5. Nex...
Page 23
3. Push the DATA INPUT lever upward for 0.5 seconds. This will cause the flashing “INH” display to change to a flashing “ON” display. Now the mixing is on. 4. Next you set the left wing to channel 1 (...
Page 24
N-TH Normal throttle curve function (HELI only) Used to set throttle curve for normal flight. 5-point throttle curve is utilized to best match the blade collective pitch to the engine RPM for consiste...
Page 25
3. Use SELECT key to select the desire curve point. Point 1 is shown initially which is throttles stick all the way downward (slow) position. Point 5 is throttles stick all the way upward (hi) positio...
Page 26
REVO Pitch-rudder mixing function (HELI only) This mix adds rudder in conjunction with pitch. This helps compensate for rotation of the helicopter caused by the increased engine torque. (Never use rev...
Page 27
• GY401: Simpler set up. Ideal for learning aerobatics through 3D. • GY502: Better centering than 401 for more advanced aerobatics. Ideal through Class III competition. • GY611: Exceptional center. Ex...
Page 28
SW-T Swash to throttle mixing (HELI only) This function corrects slowing of engine speed caused by swashplate operation at aileron or elevator operation. To activate swash to throttle mixing: 1. Enter...
Page 29
To select the swashplate types: 1. Enter the programming mode and use the MODE key to access the “SWSH” function. 2. To select swashplate type press the DATA INPUT lever upward or downward for about t...
Page 30
F/S Fail Safe (PCM mode only) The Fail Safe function is used to prescribe what the PCM receiver will do in the event radio interference is received, and doesn’t work FM(PPM) receivers. In this menu, y...
Page 31
FLOW CHART ACRO MODE FUNCTIONS To change the Stick Mode, turn on the transmitter holding MODE and (Screen at Startup) To enter or leave Programming Mode, SELECT keys down simultaneously. press MODE an...
Page 32
FLOW CHART HELI MODE FUNCTIONS To change the Stick Mode, turn on the transmitter holding MODE and (Screen at Startup) To enter or leave Programming Mode, SELECT keys down simultaneously. press MODE an...
Page 33
OTHER 6EXP FUNCTIONS Trainer switch (ACRO mode) To utilize the trainer function, the appropriate trainer cord (available separately) and a second Futaba transmitter (usually provided by your flight in...
Page 34
Adjustable-length control sticks The control stick length is adjustable to make the transmitter more comfortable to hold and operate. To adjust the length, hold the locking piece (B) and turn the stic...
Page 35
FLIGHT PREPARATION Flight preparation is to be done at the flying field. IMPORTANT: Your radio control system transmits a signal on a certain frequency. Be certain you know what the frequency is. This...
Page 36
MODEL DATA RECORDING SHEET (ACRO) (Make copies before using) Model name: Model No. 1• 2 • 3 • 4 • 5 • 6 Model Type: ACRO MENU FUNCTION CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 REVR Servo Reverse N • N • N • N • ...
Page 37
MODEL DATA RECORDING SHEET (HELI) (Make copies before using) Model name: Model No. 1• 2 • 3 • 4 • 5 • 6 Model Type: HELI MENU FUNCTION CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 REVR Servo Reverse N • N • N • R N ...
Manual Details
| Brand | Futaba |
|---|---|
| Pages | 37 |
| File Size | 1.91 MB |
| Published | May 21, 2026 |
184 views
Enter the captcha to get the download link:
Frequently Asked Questions
How do I prepare for safe flight and operation?
Carefully read all instructions. Connect the battery, switch, and servos and test on your workbench before programming changes.
What basic mixing functions are available for ACRO aircraft?
Mixing settings include PMX1 (Programmable Mixer #1), PMX2 (Programmable Mixer #2), FLPR (Flaperon mixing), V-TL (V-tail mixing), and ELVN (Elevon mixing).
Can I adjust the stick rate or limits on the radio?
Yes, settings are available for Dual Rate, Exponential setting, EPA End Point Adjustments, and specific mixer controls like rates.
How does the 6EXP handle model selection and preparation?
Use the MODL function to select the model. You must use Model Data Recording Sheets (ACRO or HELI) to record settings before flying.