Dell EMC PowerStore Power Down and Reboot Procedures Guide
Summary
This document is the Power Down and Reboot Procedures Guide for Dell EMC PowerStore Version 2.x. It provides detailed power control procedures for PowerStore T and X model nodes, including powering off using PowerStore Manager, service scripts, and physical power controls. The guide also covers powering on procedures and considerations for proper shutdown and restart operations. It is intended for storage administrators and IT professionals responsible for maintaining Dell EMC PowerStore storage systems.
Page 1 Text Content
Dell EMC Power Store Power Down and Reboot Procedures Guide Version 2.x
June 2021 Rev. A04
Page Summary Contents For Dell EMC PowerStore Power Down and Reboot Procedures Guide
Page 1
Dell EMC Power Store Power Down and Reboot Procedures Guide Version 2.x June 2021 Rev. A04
Page 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of d...
Page 3
Contents Additional Resources.....................................................................................................................4 Chapter 1: Introduction................................
Page 4
Preface As part of an improvement effort, revisions of the software and hardware are periodically released. Some functions that are described in this document are not supported by all versions of the ...
Page 5
Introduction Use the procedures in this document to power off or reboot your Power Store appliances, nodes, or cluster gracefully. As part of a robust disaster recovery plan, it is recommended that yo...
Page 6
Power control procedures preview The following table provides a preview of the steps that are required to power off or up the relevant component in your cluster: Table 1. Power control procedures prev...
Page 7
Power control procedures This chapter contains the following topics: Topics: Powering off procedures for Power Store node Powering on procedures for Power Store node Rebooting procedures for a Power S...
Page 8
Next steps To verify that the node has powered off, check the status of the LEDs in the rear of chassis. Other than the LEDs for the power supply unit, management port, and service port, all LEDs on t...
Page 9
Steps 1. Log in to the associated v Center server. 2. If there are user VMs that are not configured for automatic migration to the ESXi host of the peer node, migrate them manually. NOTE: v SPHERE Rem...
Page 10
Power on a Power Store T model node by reseating the node About this task Use the following procedure to power on (power up) a Power Store T model node when it was removed from the chassis: Steps 1. R...
Page 11
3. Wait for the ESXi host for the node to complete powering on. 4. Log in to the associated v Center server, and exit the ESXi host for the node from Maintenance Mode. The controller VM powers on auto...
Page 12
About this task Use the following procedure to reboot a Power Store T model node using a service script: Steps 1. Launch an SSH client, and connect to the appliance using the management IP address. 2....
Page 13
Power off a Power Store T model appliance Prerequisites Do not power off the appliance if you are replacing a hardware component. Identify the node that includes the faulted hardware component, and po...
Page 14
Steps 1. Log in to Power Store Manager. 2. Use Power Store Manager to identify VMs that utilize the i SCSI or FC store of the appliance. a. Select Storage > Storage Containers. b. Select the first ...
Page 15
3. If applicable, reconnect the power cables to each associated expansion enclosure in an ascending order, such as the following: Expansion enclosure 0 Expansion enclosure 1 Expansion enclosure 2 The ...
Page 16
Power off a Power Store T model cluster Prerequisites Powering off a cluster results in the mapped hosts losing access to the data on the cluster. Before you begin, ensure that you temporarily disconn...
Page 17
About this task Use the following procedure to power off a multiappliance Power Store X model cluster. The following table describes which controller VMs must be manually powered off. The remaining co...
Page 18
The Node Power LED on each node turns on when the power cable is connected. Power on a Power Store X model cluster Prerequisites Obtain the following information: Address of the VMware v Center server...
Page 19
Safety precautions for handling replaceable units Review these safety considerations before replacing any parts to avoid damage to your system. Topics: Handling replaceable units Handling replaceable ...
Page 20
Hardware acclimation times Units must acclimate to the operating environment before applying power. This requires the unpackaged system or component to reside in the operating environment for up to 16...
Page 21
condensation. Refer to Hardware acclimation times on page 20 to ensure the replaceable unit has thermally stabilized to the operating environment. NOTE: Your storage system is designed to be powered o...
Page 22
Support Notifications Learn how to disable and enable support notifications. Topics: Disable support notifications Enable support notifications Disable support notifications To avoid unnecessarily ale...
Manual Details
| Brand | Dell |
|---|---|
| Pages | 22 |
| File Size | 172.93 KB |
| Published | June 24, 2026 |
8 views
Enter the captcha to get the download link:
Frequently Asked Questions
How do I disable support notifications before powering down?
Go to Settings > Support > Disable Support Notifications, select the appliance, enable Maintenance Mode, and set a duration longer than the procedure time.
How do I power off a PowerStore T model node?
Use PowerStore Manager or a service script to initiate the power off procedure for the specific node.
What is the procedure for rebooting a PowerStore X model node?
You can reboot an X model node using a service script or by reseating the node.
How do I re-enable support notifications after maintenance?
Go to Settings > Support > Disable Support Notifications, uncheck Enable Maintenance Mode, and click Apply.