Dell Command Intel vPro Out of Band Version 4.3 User's Guide
Summary
Streamline remote IT management with this comprehensive guide for Dell Command | Intel vPro Out of Band. Designed for system administrators managing multi-client enterprise deployments, it details the end-to-end process of maintaining secure, remote access to both client and server operating systems utilizing Intel vPro. The manual covers everything from initial installation and setup (including WinRM configuration) to advanced tasks like provisioning via USB, scheduling reports, and monitoring task queues. Gain complete control over device policies and reporting for seamless fleet management.
Page 1 Text Content
Dell Command | Intel v Pro Out of Band Version 4.3 User's Guide
October 2022 Rev. A00
Page Summary Contents For Dell Command Intel vPro Out of Band Version 4.3 User's Guide
Page 1
Dell Command | Intel v Pro Out of Band Version 4.3 User's Guide October 2022 Rev. A00
Page 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of d...
Page 3
Contents Chapter 1: Overview...................................................................................................................... What’s new in this release..............................
Page 4
Overview Dell Command | Intel v Pro Out of Band for Windows Server 2011/2012/2012 R2/2016/2019/2022 Essentials is an easy- to-use application that provides an out-of-band management solution. The appl...
Page 5
Supported server operating systems Windows Server 2022 Essentials Windows Server 2019 Essentials Windows Server 2016 Essentials Windows Server 2012 R2 Essentials Windows Server 2012 Essentials Windows...
Page 6
Installing Dell Command | Intel v Pro Out of This chapter provides steps to install, uninstall, and upgrade Dell Command | Intel v Pro Out of Band for Windows Server 2011/2012/2012 R2/2016/2019/2022 E...
Page 7
7. Click Install. After the installation is complete, the Installation Completed Successfully screen is displayed. 8. Click Finish. NOTE: Select the Show the Windows Installer log option to review the...
Page 8
Using Dell Command | Intel v Pro Out of Band This chapter discusses the various operations that you can perform after you install Dell Command | Intel v Pro Out of Band for Microsoft Windows Small Bus...
Page 9
1. Enter winrm quickconfig. 2. Press y to continue if prompted Do you want to configure winrm? 3. winrm set winrm/config/client @{Allow Unencrypted="false"} 4. winrm set winrm/config/client/...
Page 10
2. Click the settings icon in the upper right side of the screen. On the Settings screen, the Indications tab is displayed. 3. Click Unsubscribe All. NOTE: Unsubscribing all subscriptions may take som...
Page 11
For more information, see Launching Dell Command | Intel v Pro Out of Band. The USB Provisioning screen is displayed. 2. Enter your Management Engine (ME) password in the Current Password section, and...
Page 12
NOTE: More information about DMTF filters may be found at the DMTF website,www.dmtf.org. Indications allow you to monitor diagnostic events such as: Motherboard failure CPU failure Power supply failur...
Page 13
4. Select the filter(s) to include in your policy. Ensure that you select at least one filter to create a new policy, but no more than two filters consisting of the Core Platform (Recommended) filter ...
Page 14
Completed Completed with error(s) Stopped To sort the Subscriptions table by any of its fields in ascending or descending order, click the relevant column title. Columns in the Subscriptions table are...
Page 15
2. Select the subscription that you want to delete. 3. Click the Delete button. Applying a subscription NOTE: You cannot apply a new subscription when the Listener IP Address setting is not set. Click...
Page 16
To refresh the Subscriptions Status table, click the refresh button. Stopping a subscription If one or more rows of a subscription are in the Ready, Processing, or Pending Retry state, then you can st...
Page 17
NOTE: When a Message ID is added to the Blocklist, previous events with same Message ID remain in the Event list; only new events with that Message ID are discarded. NOTE: Adding all events to the Blo...
Page 18
The Summary tab is displayed. 9. Click Finish. The Task Queue window is opened and depending on how you scheduled the task, it starts running immediately or gets queued. Configuring the boot order Cha...
Page 19
2. Click Client Configuration > BIOS Settings. 3. Make any changes to the BIOS settings for your client systems. 4. Optionally, select task processing options: Continue processing. Do not stop on a...
Page 20
10. You can either choose to apply the password changes immediately or schedule it to run later. Depending on the schedule, select one of the following options: Run now — the BIOS password configurati...
Page 21
The Schedule Task tab is displayed. 8. You can either choose to apply the task immediately or schedule it to run later. Depending on your schedule, select one of the following options: Run now—the pow...
Page 22
Retrieving wipe client data status NOTE: Retrieve requests the status of the Wipe Client Data operation. NOTE: After the remote hard drive wipe command has been issued from the server to the client sy...
Page 23
The Schedule Task tab is displayed. 5. You can either choose to apply the Task immediately or schedule it to run later. Depending on your schedule, select one of the following options: Run now—the Sch...
Manual Details
| Brand | Intel |
|---|---|
| Pages | 23 |
| File Size | 215.24 KB |
| Published | June 03, 2026 |
57 views
Enter the captcha to get the download link:
Frequently Asked Questions
What prerequisite steps are required before installation?
You must first understand the pre-requisites listed in Chapter 2.
How do I view my reports for client systems?
Click 'Retrieve', select the target clients, click Next, choose to run now or schedule it, and then provide a task name.
What should I do if the report task fails on some clients?
Use the 'Re-Run' function in the Task Queue window; this re-runs existing tasks while skipping those that completed successfully.
Can I perform tasks for offline client systems?
If your client systems are not connected to the network, you must run the report task again.