Dell Command Intel vPro Out-of-Band Version 3.5 User's Guide
Summary
Dell Command | Intel vPro Out of Band Version 3.5 User's Guide (June 2021). This guide covers installation prerequisites, setup procedures, repair and upgrade options, and management of client systems through Intel Active Management Technology (AMT). It supports various client and server operating systems for remote out-of-band management capabilities. Target users: IT administrators managing Dell enterprise client systems with Intel vPro technology.
Page 1 Text Content
Dell Command | Intel v Pro Out of Band Version 3.5 User's Guide
June 2021 Rev. A00
Page Summary Contents For Dell Command Intel vPro Out-of-Band Version 3.5 User's Guide
Page 1
Dell Command | Intel v Pro Out of Band Version 3.5 User's Guide June 2021 Rev. A00
Page 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of d...
Page 3
Contents Chapter 1: Overview...................................................................................................................... What’s new in this release..............................
Page 4
Retrieving reports....................................................................................................................................................... Task queue.......................
Page 5
Overview Dell Command | Intel v Pro Out of Band for Microsoft Windows Server 2011/2012/2012 R2/2016/2019 Essentials is an easy-to-use application that provides an out-of-band management solution. The ...
Page 6
Windows 7 32-bit Professional Windows 7 64-bit Professional Windows 7 32-bit Ultimate Windows 7 64-bit Ultimate Supported operating systems on managed client systems through AMT Windows 10 Windows 8.x...
Page 7
Installing Dell Command | Intel v Pro Out of This chapter provides steps to install, uninstall, and upgrade Dell Command | Intel v Pro Out of Band for Windows Server 2011/2012/2012 R2/2016/2019 Essent...
Page 8
9. Click Finish. NOTE: Select the Show the Windows Installer log option to review the installation logs. Using the repair option in the installer This feature repairs any installation issues that may ...
Page 9
Using Dell Command | Intel v Pro Out of Band This chapter discusses the various operations that you can perform after you install Dell Command | Intel v Pro Out of Band for Microsoft Windows Small Bus...
Page 10
3. winrm set winrm/config/client @{Allow Unencrypted="false"} 4. winrm set winrm/config/client/auth @{Digest="true"} 5. winrm set winrm/config/client @{Trusted Hosts="MANAGEME...
Page 11
1. Launch Dell Command | Intel v Pro Out of Band application. 2. Click the settings icon. On the Settings screen, the Indications tab is displayed. 3. Configure the following settings: Retention Days—...
Page 12
History Limit—Set the number of tasks to retain in the task queue database between 7–1095 tasks. NOTE: Only completed, canceled, or aborted tasks are removed as new tasks are created. 5. Click OK. Log...
Page 13
10. Enter a name for the certificate file. 11. Click Create Key. The USB provision key is created. Client selection This feature discovers provisioned Dell client systems on the network. NOTE: If you ...
Page 14
Recommended and optional filters Some indications are message intensive: when applied to a client, these filters will likely generate a large volume of messages, and they should therefore be used with...
Page 15
The Edit button becomes active. 3. Click the Edit button. The Edit Policy screen opens. 4. Make any required changes to the policy. NOTE: At least one filter must be selected before the policy can be ...
Page 16
Creating a subscription NOTE: You must have already created at least one policy and have clients available before you can create a subscription. 1. Click Indications > Configure Subscriptions, and ...
Page 17
NOTE: If the Indications service (Dell Awe Svc) is not running, you cannot subscribe, unsubscribe, or stop subscriptions. Check the status of the service on the Services console. 1. Click Indications ...
Page 18
Events The Events screen displays a list of indications that are returned once a subscription has been applied. From this screen, you can not only view the list of events, but also export the list to ...
Page 19
Exporting events To export a list of events to a *.cvs file: 1. Click Indications > Events in the left pane. 2. Select the events to export by placing a check mark in the appropriate boxes. 3. Clic...
Page 20
Moving the boot devices up or down the order by clicking the Up or Down arrows at the bottom of the table. Disabling boot devices by selecting or clearing the check-box next to the Boot Device. 4. Sel...
Page 21
9. You can either choose to apply the changes immediately, or schedule them to be applied later. Depending on the schedule, select one of the following options: Run now—the BIOS setting configuration ...
Page 22
Operations This feature allows you to set up KVM sessions, turn off, turn on, and reboot Dell client systems, and remote wipe the hard drives of Dell client systems. Establishing KVM sessions This fea...
Page 23
Wipe client data CAUTION: This operation deletes all the data on your client systems. NOTE: The remote-wipe of client hard drive may take several hours to complete. The Wipe Client Data feature remote...
Page 24
5. The Schedule Task tab is displayed. 6. You can either choose to apply the task immediately or schedule it to run later. Depending on your schedule, select one of the following options: Run now—the ...
Page 25
Retrieving reports NOTE: Retrieving reports requests a report for the data that are collected through Scheduled Reports. View existing reports. To retrieve a report: 1. Click Retrieve. The Select Clie...
Manual Details
| Brand | Intel |
|---|---|
| Pages | 25 |
| File Size | 220.86 KB |
| Published | May 23, 2026 |
116 views
Enter the captcha to get the download link:
Frequently Asked Questions
What operating systems does this tool support for clients?
It supports various client operating systems, including details found in Chapter 1.
How do I provision a device using USB?
You can use the USB provisioning option to set up devices that are not connected to the network.
What is the process for running a report task?
Select clients, click 'Next,' choose if you want 'Run now' or 'Run At,' provide a name, and then click 'Finish.'
How can I re-run a failed report task?
Use the 'Re-Run' option in the Task Queue window. This allows you to skip clients where the task succeeded.
Where can I view scheduled or completed tasks?
The Task Queue window is used to review all scheduled and completed tasks.