CASIO KL-70E User Guide
Summary
Discover professional labeling efficiency with this manual for the KL-70E thermal transfer label printer. This comprehensive guide empowers users by detailing everything from initial setup and daily operation to complex technical specifications. It emphasizes critical safety precautions, troubleshooting common error codes, and performing routine maintenance using AC adaptors or batteries. Essential reading for anyone needing reliable, high-quality labeling solutions in a commercial setting.
Page 1 Text Content
KL-70E
User’s Guide
Page Summary Contents For CASIO KL-70E User Guide
Page 1
KL-70E User’s Guide
Page 2
AC adaptor Important Safety Precautions Do not allow the power cord to become damaged or broken, and never modify, over bend, twist, or pull it. Never place heavy objects Note of the following safety ...
Page 3
Location Caution Avoid leaving the unit in areas subjected to high humidity and large amounts of dust. Such conditions create the danger of fire and elec- AC Adaptor trical shock. Do not leave the pow...
Page 4
Introduction Contents Important Safety Precautions Congratulations on your selection of the CASIO KL-70E Label Printer. This Part 1 Getting Acquainted CASIO Label Printer makes it possible for you to ...
Page 5
Part 5 Character Size and Text Effects Character Size Part 1 Getting Acquainted To change the character size Text Effects To specify a text effect This part of the manual provides you with important i...
Page 6
General Guide Part 2 Getting Ready This part of the manual tells you how to load batteries and the tape cartridge, and how to perform other basic setups for the Label Printer. Important! Be sure to re...
Page 7
Replace the batteries in accordance with the battery life marked on the side 4. Replace the back cover. of the battery. As shown in the illustration, hook the cover on the battery side of the compartm...
Page 8
To connect the AC adaptor Tape Cartridges Connect the adaptor to the Label Printer as shown Use the procedures described below to load a tape cartridge into the Label in the illustration. Plug the oth...
Page 9
Make sure that the tape does not extend too far Tape Width Specification past the tape guide. If it does, cut off the end with a pair of scissors. Important! When using 6mm tape, using certain charact...
Page 10
Display Symbols and Indicators Code indicator This indicator appears when you press the CODE key. While this indicator is on Before getting into actual input, you should first become acquainted with t...
Page 11
6mm tape indicator 3. When you reach the end of a line of text, press B (the L cursor key) to This indicator appears when you use the procedure on page 8 to specify you input a newline mark. are using...
Page 12
2. Use the H, J, K and L cursor keys to move the underlining to the sym- To delete characters using the BS key bol you want. Example: To change the word “commmputer” to “computer”. Not all of the avai...
Page 13
2. Input the new characters (XYZ). Important! Inputting the new characters causes them to be inserted at the cursor posi- Any character size specification you make is applied to all the characters on ...
Page 14
4. When the character size you want to specify is 3. Use H and J to move the cursor to the effect you want to use. on the display, press SET to select it and return 4. When the cursor is located under...
Page 15
Printing a Tape To print a stamp tape Printing a tape is as easy as pressing the PRINT key. 1. Input the text you want to print. 2. Press FUNCTION and then 5 To print a tape STAMP (STAMP). MIRROR 1. P...
Page 16
2. Press H, J, K or L to change the setting shown on the display between Print Density ON (mirror printing) and OFF (normal). The print density setting controls how darkly figures are printed on your ...
Page 17
4. Press SET to store the text in memory or ESC 5. Press SET to recall the text from the area that to abort the store procedure without storing is currently on the display. anything. Note that recalli...
Page 18
To set the conversion rate Part 8 Currency Conversion 1. Press FUNCTION Z (RATE). 2. Input the rate you want to use. (ex. 1.2345678) You can input up to eight digits plus decimal point, Your Label Pri...
Page 19
To select a label format To perform the calculation and print the label 1. Press FUNCTION B (FORMAT). CURRENCY A NOW 2. Use H and J to select the number of the for- CURRENCY B (Blank) mat you want to ...
Page 20
3. Remove the tape cartridge. To initialize the Label Printer Printer head 4. Use a cotton swab dipped in alcohol to clean 1. Turn power off. the printer head and roller as shown in the illus- 2. Whil...
Page 21
• Text Input Ink ribbon is being fed from the tape outlet along with the tape. Cannot input text. Possible Cause Action Possible Cause Action Ink ribbon cassette loaded Remove the ink ribbon cassette ...
Page 22
Error Messages• Using Labels Label will not adhere to a surface. Message Possible Causes Action Possible Causes Action ERR! Attempt to input two B Use only one B mark. marks within the same Only two l...
Page 23
Message Possible Causes Action FUL! Both text memory areas Delete text from one of (AREA 1 and AREA 2) the text memory areas This message already contain text. and then store the new appears on the te...
Page 24
Specifications Model: KL-70E Input Keyboard Layout: Typewriter (QWERTY) Character Types Alpha (English and other languages): Numbers: Symbols: Display Type: Liquid crystal display Columns: Character m...
Page 25
CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome Shibuya-ku, Tokyo 151-8543, Japan
Manual Details
| Brand | Casio |
|---|---|
| Pages | 25 |
| File Size | 1.57 MB |
| Published | June 05, 2026 |
58 views
Enter the captcha to get the download link:
Frequently Asked Questions
What power adapter should I use with the unit?
You must only use the specified AC adaptor (optional AD-A95100). Using any other type risks fire or electrical shock.
How fast is the label printer’s printing speed?
The printing speed of the KL-70E is approximately 6.76mm/second.
What do I do if I see a 'BATT' error message?
The 'BATT' error indicates that the internal battery power is too low; you must replace the batteries.
What precautions should be taken when moving or storing the unit?
Always unplug the AC power cord from the wall socket and consider cleaning the area around the prongs for dust buildup.